I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
When scanning, is there a built-in way to detect and ignore duplicate advertisement packets (i.e. from the same device)? Specifically, I want to instruct the SoftDevice not...
Hi.
Thank you for your hard work.
I would like to apply the Timer example to the Uart example in SDK 15.2.0.
It was able to build without any problems before the timer...
Can somebody help me to setting up debugging in eclipse (nRF52840_xxAA)? As all I use some old tutorial here . But I still can't set up debugging on eclipse for 3 years of...
Hi
We are using the nRF9160 to drive the SD pin of the QM14501 LNA, which would typically consume 740uA. While the pin is driven high, I only measure 0.7V on the pin, so...
Hello,
I'm receiving a FDS_EVT_UPDATE (FDS_ERR_OPERATION_TIMEOUT) in my fds event handler. My update didn'it work but i don't know why.
If someone has already faced this...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
hi, I am beginner , so confused how to doing write and read sequence. I want read and write sequence with register setting .please give me how to develope logic for that.
Hi,
I'm working on a BLE link between two dev kits. For the time being, both have USB drivers and handlers that will pipe data from one USB terminal to another over BLE...
I'm having a bit of trouble getting a program downloaded onto my development board. I've been using Keil 5 to program and I haven't had a problem until I started experimenting...
I'm seeing an odd behavior where the ability for our application to communicate to peripherals via twim is being affected by the initialization values for app timers.
Timers...
HI
I'd like to clarify my understanding of how the three work-
Does the SD card library use SPI or SPIM?
Does SPIM automatically use EasyDMA, or is it configured...
The API for sd_ble_gatts_hvx says that NRF_ERROR_INVALID_STATE is returned when no indications are enabled.
However, when I call sd_ble_gatts_hvx in this scenario I receive...
Hi everyone,
I am having problems reading the battery level using the SAADC. The main problem is that the reading is not consistent from when the device is booting to...
I have two bugs to report in nRF5_SDK_16.0.0_98a08e2\components\ble\nrf_ble_scan\nrf_ble_scan.c
The following functions in nrf_ble_scan.c follow a pattern nrf_ble_scan_addr_filter_add...
Does LESC is supported in FreeRTOS?
I init BLE modules in FreeRTOS tasks. After LESC is enabled, system returns error in nrf_crypto_rng_init(). Looks like nrf_stack_info_overflowed...
