I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
LAST EDIT AT END OF POST
We are using a custom board with an nRF51822 programmed with a modified beacon application (which worked several months ago). After opening MCP...
Hi,
Everyone,
I am Using S130 and sdk 11.0.0.2-alpha with nRF51422 chip.
I have two crystal in my custom pcb,
one is 32 Khz crystal for LFCLK between XL1 and XL2 (pin...
My application is using the FIFO UART module to communicate with another MCU. It is also running softdevice S132 v2.0.0.
While most of the time everything runs smoothly...
Hi
Are there any major OSes/stacks (e.g. Linux, Android, iOS) that provide support for the L2CAP feature so that we can test our Nordic device against?
Thanks
Hi,
I would like to know what is wrong with my code, which is presened below. Each time the timer is triggered I would like that the program writes four bytes into the...
I have a project that requires a bluetooth central to be used to gather data from a HRM service, which shouldn't be too much of an issue. However, it also has to store this...
I have searched here for an answer to this, but cannot find exactly what I am looking for. I am trying to put my Rev3 51822 to sleep and wakeup via GPIO. When I enable GPIO...
Whats the best way to secure my advertising packets such that others cannot make sense out of it?
Do we encrypt the packet data so that it is gibberish, random and not...
Hi!
We're running a S130 Stack to act as both Peripheral & Central at the same time. Everything is working fine but i i'm not quite sure about best approach for handling...
Hey ,
My application stores the data on BLE disconnect to pstorage succesfully.
But on reset if i try to read the data from pstorage it stops advertising, but the pstorage_load...
Hi,
I am using nRF52832 with S132_V2.0.0 and SDK_11.0.0.
I am able to doing dfu of softdevice and bootloader individually but when i try dfu for combined (SD + BL) then...
I can't find nrf.exe in C:\Program Files (x86)\Nordic Semiconductor\Master Control Panel\3.10.0.14\nrf
I only find nrfutil.exe in that folder.
Shall I use nrfutil.exe...
Softdevices have several separate version number systems:
a) the human-readable release version - used for hex file naming.
e.g. s110_nrf51_8.0.0, s120_nrf51_2.0.0
b...
