I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
Hi
I wrote a softdevice, bootloader and application using the nRFgo Studio.
When I turn on the device, bootloader_settings_t is all 0xFF so bootloader_app_is_valid returns...
I went to so many references and definitions of variables and functions but I can't seem to find where is decided to use either spi_master_0 or 1.. where is this magic config...
I am a freshman. And I am doing some research on BTLE by nRF51822-EK. I want to get RSSI. Could you please tell me if there is a reference code or project in SDK? Is there...
Hey,
For my project I wrote and tested (w/ nRF51 DK) all firmware in mbed. I also made a custom PCB w/ the nRF51822 CEAA chip based on the 4 layer reference design provided...
HI,all!
I want to know if BLE can send data to APP in form of String instead of Byte?(the examples all send in form of byte )
If it does can, can you mainly introduce...
Hey everyone,
I'm trying to print floating point numbers to the UART to debug my application. I know the nrf51 is doing the operations correctly because if I convert the...
Hi,
I'm using the following TI IC www.ti.com/.../tps62736 to get 3V from a LiPo battery. It has a VIN_OK pin that I can configure to alert of battery low level. The problem...
Hi,
I am trying to get even a basic ARM GCC example set up using the provided toolchain code, and am having a rough go at it.
First, what is the most recent, working...
In the s110_nrf51_8.0.0_migration-document.pdf, the ROM and RAM start and size for the v7.0.0 and v8.0.0 are specified as follows
s110_nrf51_8.0.0
IROM1 - Start...
What should the connection or other settings be to have a peripheral always connected? It is a bit contradictory for low energy device, however for a lost&found (link-loss...
Hi,
I just started on developing on the nrf51-DK. I started with blue_app_proximity, and I am trying to hack the immediate alert to do a toggle a led. I initialize the...
Hi,
I am trying to save/restore some configuration variables to/from the flash storage. If I do it using S110, it works perfectly fine and I can both store and read values...
Hi,
I have the same problems as described in devzone.nordicsemi.com/.../
I'll post details here as requested. I do the following:
-Connect P0.30 to ground (see photo...
We are working on a BLE home automation application. It is likely that some homes could have 10 or more of our devices. We also need to allow the homeowner control of which...
