Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi
I'm trying to use the nRF Cloud Provisioning Service with the nRF Cloud multi-service sample in SDK 2.6 on a nRF9151DK.
I have got the token from the device using AT...
Hi,
Do you have sample ios reference code for app that I can start developing?.
I have been searching the web and couldnt find a good example. basically for updating firmware...
I use ncs v2.7.0.
I am evaluating to connect 250 nodes in BLE network . Each node sends BLE packet periodically for every 100ms.
In project sample, periodic_adv_rsp.c...
Hello,
I am running the SDK on Fedora 41 Workstation using VSCode (Codium) with NRF Connect SDK Extensions. Everything was working fine with v2.7.0 SDK installed using the...
I am having nrf52840 dongle,my purpose is to make it a peripheral device,enable gatt,change tx power through gatt.i uploaded blinky hex code(compiled in vs code ) to the controller...
I am using nRF52833DK, zephyr v2.7.0.
I want to disable hardware nRST to use P0.18 as GPIO.
What I did
Added to Kconfig : CONFIG_GPIO_AS_PINRESET=n
Removed : gpio...
I previously tested the peripheral_ams_client with iOS 17, and I could select the device in iOS Bluetooth settings to connect to it, however it appears in iOS 18 iOS is not...
Dear: We have product using nRF51822 with BLE to UART bridge between an app on the phone and the UART interface on the nRF51822 device. that include control command and OTA...
I want to implement a PWM up/down ramp that preferably runs with no CPU involvement. From the datasheet it seems I can do this by storing a sequence in RAM and having the...
Programmer tool v3.0.9 outputting the error - " Failed to detect device after reboot. Timed out after 10 seconds." After the user attempts to write a blinky hex file to a...
Hi,
My Development Kit is PCA10040, SDK_17.0.2.
I have builded the example code -> \nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_uart\pca10040\s132\ses
in...
Hi, I have multiple nRF52840 Dongles and need to set one of them to permanently stay in advertising mode, even if a device disconnects.
If I use the nRF Connect tool to...
Hi,
I click on the device tree editor icon in VS-code and I see nothing
although I have an open working Zephyr nrf connect application in VScode.
I installed nrf...
Hello DevZone,
I'm building a Matter development environment with OTBR and CHIP-Tool:
NB: Ubuntu 22.04 with WIFI and BT, get CHIP tool from official pre-built (V2.5...
I am trying to install the nRF_Connect_SDK and associated toolchain under Linux Ubuntu ARM64. I find from other postings here that nRF_Connect_For_Desktop is not available...
