Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
Working with an nrf52805. Copied a simple example (peripheral_LBS) and found that RAM overflowed by ~2.2K I note that the nrf52dk_nrf52805 is not listed as a "compatible"...
Hi Team,
I am using nRF52840_DK to program my custom board but I am facing some voltage related issue from VDD pin.
Measuring on board it's giving 3.0V for VDD & GND but...
Hi
Two questions as below
1. About nPM1300 & nRF54L15 I2C connection, at nRF54L15 side, I put SCL/SDA at P1.x group, so INT also need at P1.x group? Or I can put at P0...
https://academy.nordicsemi.com/courses/bluetooth-low-energy-fundamentals/lessons/lesson-4-bluetooth-le-data-exchange/topic/blefund-lesson-4-exercise-3/
There are two "Section...
Hi,
I have designed a custom board using the nRF52840 and have successfully programmed it using SWD (SWDIO & SWDCLK) with a J-Link programmer . However, I now want to program...
Hii,
Downloaded Timer code from sample and trying to build using 2.9.0 SDK but not able to build. It is building using 2.6.2 sdk.
Pls check and update soon.
Thanks...
Hello.
I started using a custom board with the nRF5340. After flashing the program, it seems that protection was enabled, and operations such as erase, read, and write became...
Hi ，Nordic team
I applied QSPI driver QSPILCD and encountered the following problems: question 1, use nrf_drv_qspi_write write data: header and tail will be a few more bytes...
I'm trying to migrate my project from the child/parent build system to the new sysbuild system in Zephyr, and I'm finding it a bit unclear. I came across a helpful post that...
I used to use ncs2.8.0, but now I have updated it to 2.9.1. I upgraded the SDK and toolchain to version 2.9.1 in VSCode, but encountered this prompt when selecting version...
Dear Sir/Madam,
In the NRF date_time_ntp.c, the fraction of the NTP message is completely ignored in the line:
* date_time_ms = ( int64_t ) sntp_time . seconds * 1000...
Hi there, I have a nrf54l15 pdk and i want to get any uart log with my kit. I tried the quick start hello world code but it wasn't load application core and reset device....
I sometimes have bonding issues. Most of the time, bonding works fine. But occasionally, It looks like the Nordic SDK on the peripheral sends messages too early. The peripheral...
