Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
i have connected usb type(b) to j3 and kept the switch to usb but no advertsing happens and i have also connected external supply 3v to p21 the board is not on . only while...
Using Zephyr in NCS 2.8 on nrf5340/nrf7002 wifi combo, and trying to get https to work. I'm using the option where the TLS setup is done in the socket layer (enabled in prj...
I’m trying to set up a simple relay using an nRF52840 board to route data between a BLE central (my phone) and a 9600bps UART device. My goal is to send data from the phone...
i've captured the following using a joulescope js-220 as an inline current meter across the VDDM CURRENT MEASURE jumper on my rRF54-DK board....
i'm running the system_off...
Hi!
I'm storing a key in the KMU for use by the ECB.
If I set the slot's destination address to an address in RAM, the KMU pushes the key there correctly, but if I instead...
Hi,
I have a custom board, i enable the adc peripheral, and it generates:
then i connect the AIN4 channel and it generates:
but when i build i get the following...
Hi, I'm looking to develop an out-of-tree driver for the SIM800L modem. The reason I want to develop it out of tree is that I don't believe have the skills or resources to...
HI
I previously disabled DCDC in the app using the following method:
in app.overlay
I am using ncs 2.9.0 I saw some posts using CONFIG_ENABLE_DC_DC=n , but I am unable...
Hi,
I'm try to set up a UDP server on a nRF9151dk, and send data from a remote pc to the devkit. I have tested my sim and networking works correctly, I am able to use coap_client...
Hi,
I am using the nPM1100 in my new application, where the system power circuit includes two additional 250mA LDOs configured to provide a 3.3V output . I am also using...
Hi,
I am encountering the following build error with the BLE peripheral example after migrating from NCS 2.7.0 to 2.9.0 and when CONFIG_BT_LL_SW_SPLIT=y is set in prj.conf...
Hi,
I am using nrf Connected SDK v2.6.2 on windows 10. I try to create a blank application project for the device ADXL363 on SPI2 bus on the nRF9160DK board.
I basically...
hi:
I use ncs 2.8.0 ,nrf9151 dk and v2.8.0\nrf\samples\net\https_client.
I modified the DigiCertGlobalG2.pem
this is log:
connect() failed, err: 111.
What is the...
Hello,
I was wondering if there was a way to implement a physical on/off switch to the npm1300 that would allow the outputs to be isolated form the battery but still having...
We have designed a vehicle tracker that uses the NRF9160. We have found in the past that sometimes after the radio has been running for a while it gets into a loop where it...
