It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi,
Is it at all possible to use the QSPI interface of nRF5340 to interface a micro SD card? Is sending custom instructions combined with long frames, as suggested here...
Hey Nordic team,
We have ECG/EGM alignment problem over BLE, the peer ble chip use RSL15, they came up with the below algorithm, which do need an API to get connection...
Hi all,
I am having a ble 5 beacon broadcast on my nrf 52840 chips. I would like to know that if it is backward compatible so that ble 4 smartphone can receive the packet...
Hi,
Running the asset_tracker V1 i obtain a LTE connection and date time:
[00:00:19.338,226] [0m<inf> asset_tracker: DATE_TIME_OBTAINED_NTP
I want to convert it...
Hi
I am a new person for nrf5340, I got the NRF5340 PDK. I unbox and check that four buttons. It works fine. Then I compile the blinky code and upload it to the board using...
Hello Devzone,
For my project I am using NFC and I am using the writeable NDEF message project as an example.
Everything is working except I have found one issue.
...
Hi Nordic Team,
I have one doubt which I can not able to understand.
Actually in my code I'm scanning some ble devices also in main infinite loop I'm reading some sensor...
We're using the CMW500 to talk to the NRF9160, and it connects ok but then gives the message "RRC Connection Reestablished". We tried using the asset-tracker example, which...
Hi, I have made the custom board without 32.786kHZ (low frequency clock)
I am trying change it to
RC OSC
HFCLK
but i tried to make the changes but debug doesn't...
Hello
I'm using an NRF5282 and this thread :
https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/simple-application-level-authentication
I try to implement...
Hello, gentleman!
We are developing our nRF52840-based application using nRF Connect SDK v1.4.2. I know there is a NCS v1.5.1 already available, we plan to switch to that...
Hi, I am trying to get start nRF5340 and projects. In NCS 1.5.0
i am following this link https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_nrf5340.html...
Hi,
I found that after a DFU my application is slower to start up by about 200ms. However when programmed initially (via a physical connection) its fine. Its only after...
I hope to send a message from two slave to one master using nRF52 through bluetooth.
I send a message from a slave to a master with ble_app_uart_c and ble_app_uart.
And...
