Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
I've been using ICMSG's IPC to exchange HCI messages between the netcore and appcore, and using SPI to exchange HCI information between the host and appcore. This setup enables...
I'm working on implementing a Bluetooth Mesh network where each node periodically sends messages containing a single float32 value or an array of float32 values (e.g., every...
Hello,
I update ncs from v2.3.0 to v2.8.0 in matter windowcovering project.
my prj.conf file:
CONFIG_PM_DEVICE =y
CONFIG_PM_DEVICE_RUNTIME =y
CONFIG_USE_SEGGER_RTT...
Hi,
I'm developing a firmware based on Zigbee CLI sample. And I enabled DFU of app core and net core via serial with serial recovery mode.
Using SDK v2.4.2 and nRF5340...
Hi,
I am trying to integrate i2c code in peripheral_uart example from ncs 2.8.0.
I am following the steps as instructed in this exercise:
Exercise 1 - Nordic Developer...
I have nRF Connect for VS Code v2024.11.75 and am using SDK 2.6.1. In Lesson 3, Exercise 1 of the nRF Connect SDK Intermediate course in step 8 the instructions show to open...
I am a long time user of Doxygen and I am familiar with its format. I have been using Doxygen manually in my nRF9160 code and it is working fine. I am using DoxyWizard to...
Hi I am working on a project where I am trying to implement Bi-directional communication between 2 nrf modules connected to stm32f411ve dev boards. I am facing issue with...
nrf52840 with the official usb hid_generic routine transplant, the computer's 2.0 port hot swap probability is very small power-off restart, other ports are not tested out...
1. dts config file, I2C_SDA is configed GPIO P0.09/NFC1 , I2C_SCL is configed GPIO P0.10/NFC1, months ago, I'm using the old SDK, I also found that these pins configed as...
Hi Nordic team,
We need assistance in determining the appropriate GPS mode for our application: A-GPS or P-GPS? Though we believe A-GPS is more suitable for the use-case...
Hello,
My coleagues and I have been developing our application on the nRF5340 Audio DK for a while now and everything is working fine. Now we are at a stage where we want...
I am working on a custom development board with nRF5340 MCU. I have used two mics and integrated the LC3 codec library. I have assigned the following spaces in the prj.conf...
Hello,
I'm using a nRF5340 DK and ncs version 2.3.0.
What i try is, to use calls like
sdc_hci_cmd_vs_zephyr_read_chip_temp() that is available in header file sdc_hci_vs...
How can we retrieve all network devices RSSI/LQI value? Is there option to subscribe value for LQI ? We just want to showcase LQI/RSSI on server so user be aware if device...
