Hi,
firstly, I have to say, I use MBED OS, if you cannot help me because of this, I understand, but maybe somebody still has some general Ideas.
I am trying to build an...
Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
I've downloaded S130 SoftDevice and found an example s130_demo_app which contains a project file for Keil v4, but when I am trying to open it in Keil V5 (that is the only...
Hello -
I'm not having any success using my PCA10024 as a dongle for MCP. Here is what I'm doing so far....
Remove PCA10024 jumper from P0.30-GND.
Connect PCA10024...
Greetings,
I am trying to minimize my BOM line items. Can C10 decoupling capacitor stated as 47nF/X5R on the reference design be replaced with 100nF/X5R without consequence...
Hello,
I know that this question was here before, but I've read all of the questions and answers and still I don't know what I do wrong.
I'm using 3 PWM channels to...
Hi,
I modified the uart_example project for the pca10001 board of the nRF51822 evaluation kit to make it work with a UART TTL JPEG camera. So far, the camera can receive...
Hi,
There was a thread about using PAs (and not LNAs) with the nRF51 a while back with some good advice.
One question I still have: is there currently any way to support...
The nRF51 Series Reference Manual v3.0 notes the potential need to set the OVERRIDEx registers in the radio mode to values from FICR.BLE_1MBIT to meet deviation requirements...
hi, i am working on a project which needs a relatively accurate high frquency clock. when i ran my program without softdevice, the HF clock's accurency could fullfil our requirement...
I'm trying to update the 51822 beacon example to work with iOS8 (iBeacon).
So far, I have registered to get iBeacon license from Apple, and setup the tools for compilation...
As the title states.
The DFU controller for OTA updating of the nrf series is described in the documentation of SDK 6.0. It is possible to flash the nordic USB dongle with...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Hello -
I'd like to make sure my RAM/ROM layout for the nRF51822_XXACis OK - if someone has a minute to double-check it that'd be great.
I started with the "nRF51822 Beacon...
Has anyone been able to get the examples to work on PCA10028?
I went through the following steps:
Used nRFgo Studio to flash in s110_nrf51822_7.1.0_softdevice.hex
Downloaded...
Hi,
Could I write or update flash without softdevice ?
Due to I must update softdevice on our product, but it doesn't have any JTAG Interface,
so, I want to use our application...
