Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello!
In the description of the usb module, I found the registers: NRF_USBD-> DPDMVALUE, NRF_USBD-> TASKS_DPDMDRIVE and NRF_USBD-> TASKS_DPDMNODRIVE
" State D+ and...
Hello,
I have been writing to my nRF9160 for the past few weeks now, no issues. My board was working fine yesterday. I left it on overnight to see how much battery it...
Info:
Windows 10
Segger Embedded Studio V5.20a
SDK16.0.0 & Mesh SDK 4.1.0
nRF52840 & nRF52832
I'm setting up a friend node and a low power node. The friend node...
Have used nRF Connect V3.30 for the past year to program nRF52DK with USB and nRF52832 BLE modules with Segger J-Link Base programmer without issue. Updated programmer app...
hi ,
I am working on the nrf525832 , i want to store the data which is sent from phone via BLE using nrf toolbox . I tried to merge the flashwrite and ble_app_uart example...
Hi,
I have some questions regarding BLE:
1) What is the max payload size? Where can I find it?
2) What is the throughput in bps? Where can I find it?
3) Where...
Dear Members,
I got the value for cadence, speed and HRM, then display it to LCD,
but after they are all (the input) in 0 value,
LCD is not displaying zero, but still...
Hi,
Recently I am using BLE for transmission on zephyr on nrf52840 When my peripheral establishes a connection with central, the subscription is also successful My peripheral...
The chip runs in the app stage and calls a function to make the chip jump to the bootloader stage (DFU mode).
The SDK we use is nrf5_ SDK_ 15.3.0_ 59ac345,
We made the...
Hello!
I have the NRF9160 DK set up to use UART2 and listen to AT commands from external MCU, NRF52840 DK configured to send using UART0.
The NRF9160 set up is done, pins...
I want to transfer 1000Bytes. if I transfer 1000bytes every second after some time connection broken,
and need to reboot the device and connect it again
how can I solve...
Hi, I get my first experiences with nRF905 modules (module DAYCOM M-FM-NR905 including spring antenna from Pollin) connected to ARDUINO DUEs. SPI communication works fine...
I'm designing a two layer board. I need to route the power supply to several parts while avoiding cutting up the ground plane. I'm consider running the power line on the opposite...
Hello
I'm trying to control the neopixeled WS2812. I referred to the following site.
https://electronut.in/nrf52-i2s-ws2812/
I'm going to use this example of neopixel...
Hi!
I'm developing serial communication programming on nRF52840 DK to get the UARTE1 communication on SDK 12.0.2.
I want to use app_uart_put or NRF_LOG_INFO function via...
