Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hi
For our semester project, we develop a box that has to reads some parameters from an oil pump system and send data to the cloud. As we wanted to make it independent of...
Hi everyone,
Im looking to put together a security solution consisting of an accelerometer and a proximity beacon. The accelerometer would be installed on gates and authorized...
As part of our evaluation on the Nordic BLE SOC, I want to measure the throughput, range and the power consumption.
Can someone point me to any sample program(s) that I...
A while ago I was experimenting with the usbd_msc demo, trying to get the firmware working as RAM-disk-only storage, without any permanent storage like Flash or SDC. While...
Dear Team,
We need a SoC which can support the following features for our wearable product.
1) Battery Charging
2) I2C interface for sensor
3) GPS
4) BLE
Regards...
Hi, I have run light switch example in SDK 15.2 and SDK for Mesh version 3.1.0, when I try to add new app_onoff_server_t model to Server with my code:
and I have modified...
Hello,
i noticed that even i send AT%XMODEMTRACE=0 with response "OK" the bsd lib triggers EGU0 / Trace interrupts. The modem is not started, but the bsd lib got succesfully...
We are using a Raytac MDBT42Q (nRF52832) Bluetooth in one of our products.
We are using nRF Toolbox for Android/IOS for testing. Is there any Windows 10 nRF Toolbox??
...
hi guys, I'm confused about bluetooth 5. Is there some example that use it? i have a nrf52840 board and i will like to use it in order to send my data but i didn't find any...
HI
I am trying to develop a mesh network using nordic mesh SDK..where nrf52 dongles will be beacons for which beaconing example will be used and from SDK
52840 DK will...
I startet evaluation with nRF52840 and SES.
I found the BSP Demo to crash (HardFault in Debug) after app_timer_init() , because of a NRF_LOG_INFO() inside, but Logging not...
Hi Sir,
As the title, can 51824 support BT 4.2 in Zephyr? Any document (or link) descript this?
If yes, which SDK version we can use?
Thank you.
BRs, Han
Hello,
I am working on nRF9160dk. I want to send gps coordinates via sms using nRF9160dk. Last week, I tried simple_at program to send sms and it worked. Now I am working...
When I am receiving data from slave data is missing. Means if o am reading 255 bytes then 127 bytes are right after that I am receiving alternate bytes. Some times I am receiving...
