Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
This is both a general tip for users and a question; does anyone have good success with the LIS2DH12 double-tap feature? The 3-axis accelerometer works well but the use of...
Hello-
I'm working with the " Experimental: Wireless UART Example".
Is there any way to periodically send data rather than just typing data into terminal?
hi,
I used nRF52932QFAA ,SDK14.2 uart bootloader.it works well with softdevice loader 5.0.0.But when I download my app(without softdevice),it cannot work.
Flash composed...
Hello Noric Dev Zone members,
we are looking for a Firmware developer supporting us in bringing Hyko to our customers.
What we are working on is making energy heroes in...
Hello.
I wanna develop customized bootloader using C.
There's two purpose for this.
1) Select application area : Slot 1 for main application and Slot 2 for new...
Hi,
Does the nRF52832 support the Connected Isochronous Streams (CIS) / Channels and Connected Isochronous Groups (CIG), either using nRF5 SDK or nRF Connect SDK?
I would...
Hi,
I am using direction_finding_connectionless_tx/rx sample, and NCS v2.6.1 for AoA. I made some modification on the rx side to stream I/Q data via serial port, and read...
Hello,
I am running into a problem with my Thingy:53 device where I am unable to load up the bootloader. I has the edge inpulse application working well yesterday, after...
Hello,
I have the nRF54L15 PDK and am experimenting with the intermediate tutorials for the Zephyr RTOS. I am working on Lesson 1 - Exercise 1 ( https://academy.nordicsemi...
nRF Connect 5.0 crashes after asking to install nrf-device-lib-driver-installer.exe and shows the following cryptic message.
Trying with nrfconnect-setup-4.4.1-x64 raises...
Hi,
We have a nRF5340-DK board with the following setup:
b0 as the first stage immutable bootloader
MCUBoot as the second stage upgradable bootloader, which needs...
Hello, I have an issue with a project I'm working on with a nRF5340 Audio dev kit. I am using VSCode with the nRF Connect SDK plugin, and SDK version 2.6.1.
I need to have...
Hi,
We are working on nRF5340 with TF-M enabled and iOS application.
What we are observing is the peripheral device MTU TX and RX are configured to 512 bytes whereas the...
Hi I'm using nRF7002-DK kit and I noticed that the output voltage of a GPIO is 1.8 V instead of a 3.3 V. I have encountered a solution mentioned that we should apply these...
I’m working on an nRF52832-based project using the Nordic SDK (v3.5.99-ncs1-1) and MCUboot for OTA updates. I have a 512KB internal flash and 4MB external SPI flash (P25Q32H...
we are using SPI3 in nrf52840 with nrf SDK 16.0
we are using this as below
1. SPI3 init -polling mode
2. SPI3 unint
3. SPI3 init - DMA mode
4. SPI3 unint
5. SPI3...
Greetings,
Is the command toggle_dcdc_state supported in the radio_test sample when compiled for the nRF5340? ( https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/samples...
I started with the BLE provisioning sample (ncs\v2.7.0\nrf\samples\wifi\provisioning\ble) using nrf7002dk/nrf5340/cpuapp build target with sysbuild which works fine to provision...
During the setup process for nRF Connect SDK v2.4.0, an error occurred preventing the SDK from installing correctly.
The environment details are as follows:
* macOS...
