It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi, Support team,
When I use the SPI peripheral communicate with nrf24l01+,it's no data return in m_rx_buf by using the API nrf_drv_spi_transfer(&spi,m_tx_buf,1, m_rx_buf...
Hi,
I use the FDS on our project firmware. The firmware saves some configurations to FDS at shutdown and the factory reset. At this time, sometime fds_gc() does not call...
Sometime, the timer handler is not call immediately after calling app_timer_start().
environment - nrf52840 - SDK 15 - with FreeRTOS - timer task priority is higher - timeout_ticks...
Hi,
In the nRF Mesh mobile app, when you go to the settings tab, you can hit "Reset Network", this appears to clear any previously provisioned network, and lets you start...
Hi all!
We've been time-stamping GPIO events using PPI in nRF52 , and it works* !
...but when using the SoftDevice , it apparently clashes with the PPI about 30ms after...
Hello,
I have been having issues when using the UART libraries (app_uart.h) with certain pins on the nrf52832. Previous iterations of our project have worked correctly but...
I am investigating an H4 HCI over a UART implementation for a client which plans to use the 52832 (or 52840) as a replacement for a TI BLE chip in a new design.
I have built...
Hi all
We are using customized board with nRf52810 chipset.
Actual requirement in our project is to send 100 bytes of data for 10 millisecond.
Kindly suggest a procedure...
I'm developing multiple peripheral and a central. Central is only scanning and Peripherals are only advertising.
In the example, I see that I should use the ble_app_blinky...
Hi,
I was trying to run dfu mesh example according to this. I attempted quite few times but every time having an error at step 11.
infocenter.nordicsemi.com/index.jsp...
Hi, Nordic Team
My development environment is PCA10028, SoftDevice 130, SDK12.3.0
I use a s130_nrf51_2.0.1_softdevice.hex.
It is based on ble_app_multilink_central and...
I am new to Nrf52832.......I have started development of a custom board based on Bt832 and BT832X.
I have built 2 proto boards one with BT832F and the other with BT832X...
Starting idle task using Task Manager library frequently throws error "Unknown function at 0x000008C8" when running with the debugger (often takes several restarts until it...
Hi
I'm using sd_app_evt_wait(); to go into low_power mode. For some reason it coming back , but I can't figure out why.
Peace of code I am executing is;
while (nrf_fstorage_is_busy...
