I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
I have shifted from silicon labs for BLE project. In Si labs we have burn BLE bootloader and BLE application separately. Do i need to do the same here in nrf controller? If...
I am unable to detect any i2c device when connected to the Nordic nRF54L15 DK kit. I have change the voltage from 1.8v to 3.3v and Tried and explore other pins in Port 0 and...
Hi All,
I have to implement an I2C Slave on my nrf52833 BLE project which is currently working (SDK 2.9.2)
I need some confirmation with the following step:
I have...
I am using the 54l10 chip, and after compiling the project, I will receive a hex firmware and a zip update package. The bin firmware and hex firmware in this update package...
Hi,
I faced with an initialization issue of combination two features: MCUMGR and UART_ASYNC_API. I get a crash right after the FW starts. It looks like the SW configuration...
Hello, I need to configure and compile a sample to send an audio stream (mp3) to the I2S interface.
I tried to put together some configuration from other samples but no...
i'm using DFU for my project, it worked fine until devices has been bonded , DFU cannot work again. i checked and find out that after running interrutps_disable() , the devices...
Hello, I am using an nRF51822 chip, configured to run as a SPI slave. The device receives commands from master, sends commands out of the radio, and relays back RF payloads...
Hello,
I've created my own custom model which allows a client to control the duty cycle of a couple PWM outputs which are on the server. My model is quite simple, it just...
Dear all,
We're started studying payment via BLE with NRF52. But i looking for in Nordic website and google it seem a little subject and document. Can Nordic expert supply...
Hello,
I am getting really confused when using te SAADC to convert the read values into voltages.
I have seen that the example ble_app_proximity() uses the following...
I'm using 14.2 SDK SES . I'm trying to send data of sensor through BLE . When i enable Notification in mobile applicaion (nRF connect) i generally dont get any value or garbage...
Hello, I'm trying to port my code for driving spi memory (S25FL256S) from nRF51822 to nRF52840. I'm using nRF52840 Preview DK, S140 and SDK 15.0.0. On nRF51 I used custom...
Hello everyone,
I'm using PDK 52840 as Programmer/Debugger for our target board with nRF52840 chip. We have also other componen which need 2.5V voltage (down from 3v)...
I'm new to both the nRF52 family and SPI, and I'm working on an SPI master nRF52810 (using the PC10040e setup). I'm compiling using GCC and makefiles. I've set NRFX_SPIM_ENABLED...
I try to make a simple project based on a "simple message model" ( https://devzone.nordicsemi.com/f/nordic-q-a/29836/send-and-receive-a-string-via-access-layer ) with Mesh...
Hi，
SDK：nRF5_SDK_15.0.0_a53641a
Chip：nRF52810
Example BLE：ble_app_uart（pca10040e \ s112）
Example 2.4G：esb_prx（pca10040）
I am working on BLE and 2.4G integration...
Hi，
I use SDK is ：nRF5_SDK_15.0.0_a53641a
But the SDK version in the link seems to be lower
devzone.nordicsemi.com/.../setting-up-the-timeslot-api
I am going to step...
I'm developing an application to communicate with a smartphone. I have the need of writing characteristics with the size bigger than the negotiated MTU, so I'm exploring Queued...
Hi guys, our team now are trying to used nrf52832 to stream audio to ios app, and as you know we are in trouble.
Here are some info about our test env:
1. mobile app...
