There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hello Nordic Support Team,
I am currently working with the Arduino Nano 33 BLE (ABX00030) , which features the nRF52840 SoC , and I am interested in accurately measuring...
I want to read the RSSI. The code is shown as follows: ，However, after compilation, the error message displayed is: "undefined reference to `bt_hci_cmd_alloc'".I need to know...
Hi there,
I am seeing inconsistencies with the PCB layout specification of the nrf7002.
1) In the v1.1 of nrf7002 datasheet, it is recommended that the following capacitors...
Hello, we are currently testing the output of square waves through GPIO output pins. However, I found that a single operation to set the GPIO output pin high or low using...
I've installed the same version of the Power Profiler V4.3.1 on Linux and on windows.
On windows the device gets recognized straight away and I can use it, on Linux however...
If I understand correctly, you can pretty much assign any pin to any peripheral. I've been using a modded central uart project on a dev board but on this other board I'm using...
Hello,
is there any way to access the Stack and Heap Start/End memory addresses from the zephyr code?
I have found the __INITIAL_SP definition that gives the Stack start...
Hi,
I have been working through the Dev Academy cellular course using the nRF9151 DK which is fitted with a 1NCE MFF2 eSIM. I was able to set this up in the Board Configurator...
Hello Team,
I am using the nRF52833 with the nRF Connect SDK (v2.9.1) in VS Code , and I am experiencing an issue with the RTC calendar update.
I initially set the RTC...
Hi everyone,
After a debugging session using the debug tool in nRF Connect SDK with an nRF52832 on a custom board, the chip is now completely unresponsive—I can't flash...
Hi, Recently we upgraded to nrf-sdk 2.7.0 (previously on 2.6.1) and I began to notice that NFC had stopped working for our project, when running on nrf5340dk.
While switching...
To preface:
Board: nRF9151DK
nRF Connect SDK / Toolchain: 3.1.0
Hello,
I am attempting to learn and integrate full modem FOTA functionality into my application...
Bonjour,
We are working on a firmware upgrade for our product based on a nRF52833.
With the previous firmware, compiled with SDK 2.3.0, when the board was OFF, the power...
