There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi
I am using nRF5_SDK_17.0.2_d674dde with softdevice S140 have sample example as ble_app_template_c but when i run the code i get the following below error are as follows...
Hello,
I am compiling my BLE project on nRF5340, with nRF Connect SDK v1.6.1. I got this error: undefined reference to bt_gatt_exchange_mtu.
My code works fine on SDK...
11:14:55.624
Received status with code 0 PKT_SEND_MAX_RETRIES_REACHED, message: 'No response from device. Tried to send packet 6 times.'
11:14:55.954
Server setup...
Hello,
I am looking at the Asset Tracker v2 example and was wondering if it is possible to use the A-GPS or P-GPS services offered through nRF Cloud if I am using AWS or...
Hello,
Both parts part#nRF9160-SICA-R and nRF9160-DK are available on Mouser website but t he customer would like to check what revision is.
Could you please help to...
Also please let us know if there are any antenna design specifications.
If we use other antenna for NFC is your certification valid or we need to re-certify our product...
Hi,
I've been experiencing some very slow erase times in the erasing / programming stage. Consistently around 10s. I am using SEGGER Embedded Studio, J-Link V7.22, and...
Hi all
According to the PS of the nRF52832, the INFO.VARIANT field in the FICR is ASCII encoded (e.g. 0x41414530 -> AAE0).
Are only capital letters ('A' - 'Z') and numbers...
Hi everyone,
My task is make Uart peripheal advertisments on coded phy, for that i CONFIG_BT_EXT_ADV=1 on autoconfig.h, and I add the function bt_ready of the project peripheral_hr_coded...
Hi
I want to design a GATT service as a connectable peripheral device. My board is NRF5340-DK.
The software which I am using is NCS(based on Zephyr).Which sample code...
I integrate dfu into light_switch example. Current consumption before flash bootloader is 200uA, but when i flash bootloader it increase 1.2mA. How do i disable bootloader...
I got some Holyiot "YJ-17017-USB" dongles, which use the nRF52832. From my Windows dev environment, I want to load firmware on them (SoftDevice, etc.), but I'm not sure how...
I have an NRF52 DK, and an IM21 door sensor that advertises events. I am trying to pick up these events with the nRF52DK in the most robust way possible. I have used the scanning...
Hello Experts,
When I use a X-Ray machine to check appearance of NRF52840 . But I found out that there were some abnormal phenomen as same as a photo below:
Any body...
