hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
One last issue to crack. This one has been in production for a while and hasn't caused any issues other than a little annoyance to the customer. By my measurement when RTC...
Hello,
In regards to the nRF Connect SDK...
I am looking into the possibility of switching out the current implementation of AES used by the Bluetooth firmware. I am curious...
the pin for XL0 and XL1 is P00 and P01
but in my project, I need P00 and P01 works as UART.
I set the parameter to start inner RC clock.and find that: LFCLKSTAT show the...
my costom board is based upon the BT840F fanstell board. I know that this board is based on the nrf52840 QIAA SOC. but I also understand that nrf52840 QIAA has different configurations...
I am working on custom hardware with an nRF52840. I have added the MCU boot in my earlier development as well but this issue I have never faced before.
Problem statement...
Hi,
iam trying to write the data in nvs which i give input through GATT.i can read and write in nvs when not using gatt,BT.
I have 2 codes,1 is working but without GATT...
Hello,
Board: custom board
Soc: nRF52840
SDK: nRF Connect SDK v2.8.0
I would like to know device mac address and use the mac address in advertsing.
can you please...
This page (v2.8.0) https://docs.nordicsemi.com/bundle/ncs-2.8.0/page/nrf/app_dev/device_guides/fem/fem_nrf21540_gpio_spi.html
Suggests copying the following into devicetree...
I am trying to get std::vector to work on nRF52840 running Zephyr in Visual Studio Code running v2.7.0 toolchain , but have been unable to do so. I found some similar tickets...
Hi nordic
I've try to enable 115200 baud UART on p0.9 and p.10 but I can't make it.
I just saw a thread about 52840 can't use 115200 uart at p0.9, p.10:
https://devzone...
Hello,
Is it possible to use the filtering options provided by the nRF52840 BLE sniffing firmware for Wireshark, in Tshark? Specifically the device address filtering....
Hello, I have two questions. 1. First, are these pins reserved in the SOC level or DK level? this if from the nrf52840dk device tree. meaning, if I have a custom board, should...
