When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hello,
I am using NCS v2.8.0.
In this, when I configured the application to use OOB legacy pairing only mode, the build process failed.
Following is the configuration...
In our firmware we use BLE together with ESB using the MPSL timeslot API, with the implementation inspired by this example: https://github.com/too1/ncs-esb-ble-mpsl-demo However...
Hi,
I am trying the sample code in this regard. I have changed the I2C pins in the overllay file and bme register address to 0x77 as follows. It seems working but I have...
I am using nRF52840/nRF52833 (raytac module, original board). With the current nRF Connect SDK, is it possible to disable NFC and use ports (P0.09, P0.10) as GPIO?
I am...
Hello,
we are currently in the process of verifying the nRF LwM2M Client, specifically focusing on the Queue Mode functionality. During our testing, we encountered an issue...
Hello,
I am facing issue while initialising seed by calling "mbedtls_ctr_drbg_seed" function I am getting -0x34 error and when I analysis this I got to know that I have...
Hello,
It has been a while since I have done any controlled impedance and was wondering if someone could provide me a quick sanity check before I continue:
Here is the...
Hi,
Does nRF52840 support stable modulation Characteristics
It is found that Stable Modulation Characteristics fail during the test, and the capacitor of the debugger...
Hello everyone,
I'm using nRF52832 with SDK v17 (S132 Softdevice).
I don't know why, but I can't disable softdevice. I can enable it normally, but when i make use of...
Hi,
I’m looking to monitor LTE-M or NB-IoT packets sent by the Thingy:91 in real-time using an app or software. Currently, I’m using the Thingy:91 to send temperature logs...
Dear devzone,
I followed this instruction to use nRF54L15-PDK v0.8.1 to burn external boards. The wiring diagram is as follows:
Command line input: nrfutil device recover...
I have a Minew MSR01-B milimeter wave sensor and I would like to know if there is any nordic hardware that i could use to comunicate with MSR01-B sensor, get the data and...
Hello,
I am designing a battery monitoring circuit for a 3.0V CR2032 coin cell using the nRF52840, and had some questions. I am following the battery monitoring circuit...
Good afternoon,
I have successfully established a 2.4GHz Zigbee network using nrf52540 + Zephyr + ZBOSS. Now I need to switch to sub-1GHz band - suits better my application...
