Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
I am using a module MS12SF1(nrf5340 + nrf7002). I wanted to perform dfu over ble by using nrf7002dk_nrf5340_cpuapp_ns or nrf7002dk_nrf5340_cpuapp build configurations but...
Hi, i am trying to port my project based on the matter light bulb sample to a PAN1780 module which also uses the nrf52840 I used before.
When building I receive this error...
Hi, I'd like to trace the Bluetooth behavior of the nRF Desktop sample post-pairing. I have an nrf52840 dongle running the sniffer, and can observe advertising packets. Could...
Hi
We have a legacy product with around 100.000 active devices. We still need to distribute new firmware releases, and we are using the "Chained DFU" app for this purpose...
Currently, my environment uses a mobile network shared through a wired connection to an RT-AX57 router. I am working in the VSCode environment using SDK v2.6.1. Devices: Nest...
I am trying to connect a nrf5340dk to a Jetson. For now I am testing with an Arduino. I am trying to run the CanCounter example with a device tree overlay file. Also I would...
Hi,
I tried to implement the CAF LEDs module as described here . But when added the Kconfig variable CONFIG_LED_PWM =y I got the error message "CONFIG_LED_PWM was assigned...
Hi,
I was developing on Visual Studio Code earlier, and for some reason, I cannot build pristine. If I try to edit the build configuration, it never loads, and if I try...
Hi,
we are trying to make the NORA-B126 (specifically its onboard LNA) work with nrf sdk 2.3.0 by modifying the 5340dk dts and defconfig files as specified in the NORA-B1_SIM_UBX...
Hi there,
I'm working on NCS2.7.0 and nrf52840.
I used the chip-cert to generate custom DAC, PAI, and PAA with VID = 0x1234 and PID = 0x5678, then placed the...
Hi there,
Thanks for helping. We are using the nRF52840 DK along with the Power Profiler Kit 2 (PPK2) for power measurement. We are encountering periodic power spikes during...
Hi, we are designing a factory acceptance test (FAT) jig for a custom board containing an NRF9160 SiP. We are testing more than one thousand boards, and probably more than...
Hello
We are using a slave processor with AT command to communicate with the nRF9161 . This is working without problem
But we are initially using the Quick Start 0.2.7...
Hello,
I'm using nRF9160 as a HCI host and nRF52840 as HCI controller (nRF52840 config is based on HCI lpuart example). My application receives data over Bluetooth using...
