Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Dear Company
We are using the following component NORDIC NRF52840-CKAA-F-R7 and we have a problem in the test phase.
We have two version with the following marking code...
Hello,
I’m working with the nRF9151-DK hardware to test Power Saving Mode (PSM) functionality, but I’ve encountered an issue: The TAU timer (T3412) cannot be activated,...
Hi
Nordic engineer
Power consumption cannot be reduced after using hardware encryption. Under normal conditions, the device power consumption is 30µA, but after calling...
in nrf 9151 and sdk 2.9.0
we use cellular with aws
but here when we publish 10KB payload it take 6 sec and 6 byte payload take 1 sec so what we need to change for fast...
As per nRF54L15 datasheet, system_off current at 3V VDD is 0.8uA . I am getting negative average current when i measuring System_OFF current consumption of nRF54L15 using...
I am using the nRF52840 in QFN48 package. I noticed that the official pin description does not specify the corresponding pins for the digital microphone clock and data. Can...
Hello,
Starting the ncs 3.1.1 UART ASYNC examples on nrf52840dk and nrf9151dk, works fine.
Then I add SHELL on nrf9151 side, it crashes when getting incoming bytes ...
Hello everyone, some days ago I bought a nPM1304 EK kit. My intention was to profile this battery https://www.eemb.com/product-147 for my projects. I installed nPM PowerUp...
Hello,
I want to build a wireless mouse with the highest possible refresh rate. I'm considering using an nRF52840 dongle. How often can packets be sent from one nRF52840...
Hi, I’m currently experimenting with ESB using the standard esv_ptx/esb_prx examples on two nRF54L15 DK. My goal is to reduce the radio latency as much as possible. I'm still...
Issue: There seem to be plenty of ways to securely store TLS credentials (generated off the device), or any sort of string data, in persistent storage on an nRF91x device...
I am trying to read/write/erase in a partition of flash in NRF9151. I am building a non-secure image to have access to the LTE library. The code is resulting in a hard fault...
My task is to implement inbuilt RTC for nordic MCU nrf54l15 series. When i use the below API nrfx_grtc_init, it is throwing a error and returning a error code which is saying...
Hello Nordic Support Team,
I’m working with an nRF5340 using nRF Connect SDK 3.0.2.
I am trying to use the NFC pins (P0.02 and P0.03) as an I2C slave interface. However...
Hi,
I would like to generate a PWM signal specifically on the P0.03 pin of the nRF54L15 using GPIOTE + DPPI + TIMERS.
As far as I’m concerned, Port 0 in nRF54L15 does...
