Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hello,
I use nrf52832 and SDK 17.0.2.
I use flash crashlog to store crash log on the flash.
I enabled NRF_LOG_BACKEND_FLASH_START_PAGE = 0, which means flash log area...
Hello,
I have a problem with the GPS and more precisely the AGPS. I would like to retrieve my position with the thingy91, I created a project by taking the AGPS sample and...
So, for a while I have tried to follow these instructions: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.meshsdk.v5.0.0%2Fmd_doc_user_guide_modules_dfu_configuring_performing...
Hello,
Developing on Zephyr 1.2 and modem fw 1.2.
Developing a client LTE application. If I run the below sequence of commands periodically every 2 min:
eventually...
Hello everyone,
I am working on an nRF52-DK and getting familiar with Zephyr.
In this process, I am trying to connect with the sensor API with a "fake" sensor whose...
I'm not certain where to send suggestions, so hopefully this will do...
A very useful addition to the nRF Connect SDK would be support package documentation for Zephyr...
Hi,
I am trying to run the NCS Zephyr ADXL372 sensor sample application (using nRF5340 DK) but get the following error:
This corresponds to the following NACK error: ...
I would like to do mutal TLS on a NRF9160. I found the https sample where the firmware does server authentication. How do I add client side authentication to this example...
I have a project from 3 years ago (2018) that I'm trying to make a simple update to the application code. The code downloads via the Segger Embedded Studio and runs correctly...
A vulnerabilitiy in BLE secure connections is reported as CVE-2020-26558 : Impersonation in the Passkey entry protocol
"The Bluetooth SIG is recommending that potentially...
My application uses a NRF52840 (SD140, SDK 15.2.), very simple circuit and needs to be extremely low current consumption. I measured the current in conditions of BLE on and...
I'm trying to get a BLE example for NordicSemi nRF52833_xxAA using SoftDevice S113.
I found out only two examples but they don't compile.
Error[Go029]: Variable "sec_mode...
Hello,
Is it possible to disable the antenna pin of the NRF52 in software? I cannot see anything in the data sheet which suggests this.
We are using a third party module...
While following the steps required to provision the nRF9160 Connect for Cloud certificate, I entered the 'AT+CFUN=4' in the AT command text field and I clicked 'Send' but...
I have a working code using SoftDevice 140 7.2.0 and Segger ES on the nRF52840 DK. I made the single adjustment of the preprocessor variable BOARD_PCA10056 to BOARD_PCA10059...
