There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hello,
we are developing a machine that is in pre-production. We need to be able to update the firmware and until now all works well on android. but on IOS the dfu does...
I'm trying to get the LTE Sensor gateway running on the nRF9160 DK. The documentation says to run the HCI:UART example on the nRF52840. When I click on the link for that example...
Hi,
I need to know if it's possible get the firmware work using 52810 with 192K flash. As far as I know, S112 takes 100K, APP with secure connection takes ~85K(ble_app_hrs_pca10040_s132...
nrf52832 S132 v6.1.1
i want to write saadc data in flash, so i call "write_to_flash" function in "void saadc_callback(nrf_drv_saadc_evt_t const * p_event)"
sizeof(data_array3...
Does anyone know if Segger Ozone is licensed for commercial use if used with Nordic Semiconductor devices, similar to the use of Segger Embedded Studio? Or, do we need to...
Hello Everyone,
As mentioned above I wanna know how to send Energy Expended data from nRF51422_xxac device to BLE mobile application using HRM characteristics or HRS Services...
Hi,
I'm starting to work with Nordic Semi Develoment boards with a Thingy:91.
And I wanted test the GPS module and send it over HTTP POST using the LTE of the Thingy...
Dear,
I am using :
ncs: v0.4.0
SES 4.16
firmware: mfwnrf916007029alpha
Hardware: nRF9160 DK v: 0.8.5
I want to do:
1. Enable and get GPS position ("AT\%XSYSTEMMODE...
Dear ,
I tried to use HTTP POST to POST the information from GPS to my webserver.
But I couldn't combine 2 of them together. ( they, GPS and HTTP POST, worked well separately...
The driver timer of the slave stops when the slave disconnects with the master. The deviation is caused by the disconnection as the following picture shows. The hardware timers...
I've been using secure DFU over a bonded BLE connection with the following configuration:
S140 6.0.0
nRF5 SDK 15.0.0
nRF Connect for Android
#define NRF_DFU_BLE_BUTTONLESS_SUPPORTS_BONDS...
Hello,
I am using nRF52832 based development board (PCA10040) and softdevice v6.1.0.
I want to ask that does the feature of Periodic Advertisement of Bluetooth 5 depend...
Is there any documentation that talks about interface between board controller (nrf52840) and nrf91 on nrf91DK
How do they interface. Is there sample code to create custom...
Hello all,
I am working on the DFU on the NRF52810 custom board
I am trying with secure bootloader example PCA10040e
with sdk 15.3 s112_nrf52_6.1.1 softdevice
Then...
Central and Peripheral are connected by BLE.
The following error may be displayed when sending BLE message multiple times to the peripheral at the same time.
>> NRF_ERROR_RESOURCES...
