Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
Hi,
When using RTT for debugging on the nRF5340, after every flash i have to press the following button:
Then every time i get presented with the following dialog...
I would like to ensure that a particular GPIO pin is disconnected when an nRF52840 is powered up via the initial configuration specified in the DeviceTree board overlay file...
I get the following error when clicking flash button in nrfConnect VS Code extension with an nRF54L15 DK:
Error: One or more batch tasks failed: * 1057701224: Device error...
Dear Support Team!
I'm just about to flash an external board (nRF52820) through P19 where the MCU is powered at 2.3V. I would like to use the nRF52833_DK and the PPK2 to...
Hi Team,
We are using SDK 3.1.0 and radio FW version 1.3.7.
Trying to read RSSI, RSRP, RSRQ, SNR levels using AT command AT%MEAS but it returnns error.
Am I missing...
Hi Nordic,
I'm developing a BLE protocol on an nRF54L05, and is trying to send (On request or by notifying) up to 750 logs of data, each log being 8 bytes (1 byte event...
Hello everyone,
Im using nrf5340dk for the first time, i have built project for nrf5340dk_cpuapp and i think code is good but for some reasone i dont see a led diodes turnin...
Hello,
I had a question about the BT GATT DM Workqueue used in gatt_dm.c.
In NCS 2.8.0, the BT GATT DM Workqueue was introduced as an alternative to the System Workqueue...
Hi List, I have been successful to run my basic functionalities like GPIOs, I2C and ADC using custom board files for nrf54l15 based custom hardware.
Now, I am trying to...
Description:
Hello, We are developing a DECT NR+ communication setup using multiple nRF9161 DK boards arranged in a Sink–Relay–Leaf topology.
Each board operates as a...
While working on debugging our application firmware using the nRF9151, we ran into issues that we hypothesized as being caused by an incorrect modem clock leading to validation...
Hi Nordic team, We have a production firmware developed on nRF Connect SDK v1.7.0 targeting a Fanstel BLG840FB4 gateway module (nRF9160 SiP + nRF52840 SoC). We are trying...
