Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi all,
last week i used nrf connect app (v4.28.1) to update firmware
after i pressed DFU button and selected binary file, then it will jump a window to choose like...
We are using a Nordic nRF52840 microcontroller alongside the nPM1300 power management IC. When the battery is switched off due to low voltage (undervoltage protection), the...
Dear Nordic Support Team,
I am reaching out for assistance with an issue I’ve encountered on my new nRF7002DK board. After successfully flashing the Azure IoT Hub example...
I work on NCS 2.8.0
I add follow to CMakeLists.txt
add_custom_target (
my_release_file
echo AAAA BBBB CCCC
DEPENDS all
)
when run "west build -b nrf54l15dk...
Hey all,
I'm working on a project where data gets written to an SD Card regularly. At reset, power to 3.3V to the SD card is activated and all runs relatively well.
I...
Hello,
For my project I am making a custom circuit board which is pretty much just the nRF52832 chip and the surrounding capacitors and whatnot. I'd like to program this...
Nrfconnect 2.7 worked fine, but I updated to 2.8 and get this error.
For this line, I try to access my internal flash storage partition offset.
The macro complains...
OS:Ubuntu
Board: nrf52840DK
SDK: NRF Connect SDK (master branch)
After building provided example: Bluetooth: HCI Power Control and flashing the board, in serial monitor...
I am trying to program the BC832 ( https ://www .fanstel .com /bt832 -1 ) using the NRF52DK (NRF52832). BC832 is a Bluetooth Low Energy (BLE) 5.3 with NFC module using Nordic...
Hi I want to make changes to the BLE Controller stack to create an implementation of a NWP. It involves 'core' changes. Can I use the 'nrf connect' ecosystem as it comes with...
Hello,
I just started to understand Zigbee and I had some problem. I created 3 endpoints. In one of them (endpoint counter_ep ) I need a attribute reporting. A reporting...
Hello,
We are certifying our custom board which includes the nRF7002. Part of the spec EN 301 893 procedure for adaptivity (5.4.9.2.2.2) requires a multi-channel validation...
Hi,
I am trying to develop a small Zigbee device that has two endpoints, each with a Temperature Measurement Cluster. My starting point was https://docs.nordicsemi.com/bundle...
I am currently migrating from ncs 2.5.0 to 2.7.0 and am trying to move to using sysbuild instead of child / parent image. I have an out of tree flash driver that currently...
I'm a software guy with a bit of embedded dev experience and trying to get the LED_strip sample to work in v2.8. I got the code working in 2.61, and discovered that a 2.8...
