Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Running on Fanstel BM15M module (nrf54L15) SDK v3.1.1, I seeing a huge timing error when trying to implement a simple timer function. In the code below, I believe I have followed...
Hello,
Caught this Nordic Skydio presentation by chance this morning and briefly mentioned was the use of a dual core processor mcu. Was this the nrf5340 or some other Nordic...
When evaluating the hardware performance, we tested the WiFi speed of the nrf54lm20 + nrf7002EB2.However, the test result was only 2MB per second.I suspect there might be...
I would like to check if our observation with nPM1300's VBAT node is expected per the IC's design.
As a background, in our application ee use a low-leakage switch to isolate...
Hi,
we have made a pull request on github to introduce the LTI support in CTS client, since one of our new devices have a display and needed a user friendly way of supporting...
Hi every one,
If any body have been succeeded in adding DFU support in Fast pair locator tag on nRF52833-DK, if so can you guide me for it?
I am getting configuration...
Hi! I am using nrf connect sdk 2.6.1 and modem firmware 1.3.7 on a nrf9160. I have an application where i need to try to get a fix on a set interval and also sometimes transmit...
Hello,
I am working with NRF52840 dongle.
I built and downloaded the hid-keyboard example to the dongle. HID keyboard function looks good that a "1" is typed by pressing...
Hello Team,
I am using SDK version 17.0.1 and have implemented OTA. I have also implemented a buttonless DFU without bonding and created a Blinky application. However, when...
Hello,
We are also having trouble installing any SDK into the VS Code Ext Pack, for development on the nRF54L15-DK. Have tried each SDK from 3.0.0 to 3.2.1 without success...
Hello,
I have a functional project to access to an SD Card with NRF54L15DK and the version 2.9.2 SDK and 3.1.0 toolchain.
But I have difficulties to access to the SD card...
Hello.
Wiring 1:
wiring 2:
Background to the case: We tested this with 2 different ppk2s and always got the same results. Our custom board works fine if we wire...
Dear all,
i have a problem when i compile a project with Segger v. 8.22a (but i tried also with v.8.26) .
The message is:
Linking 'ne_eere.elf' Linking ' ne_eere .elf...
Hi, I am developing on nRF54L15 chip by using Insight ISP2454-LX variant, and while creating new board for it, I am unable to find package variants other than OFN48 (QFAA...
