Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello everyone I hope summer's kind with you (or winter, for the southern hemisphere...)
Here's the deal: my printf and NRF_LOG_INFO output zeros, while my register clearly...
Hi Nordic team,
I am using nRF connect sdk mesh light_switch example. version of sdk is v1.6.1 .
The node is detected in the nRF mesh app in my mobile.
what does group...
I believe I'm following both the Cypress data sheet properly. Yet I'm still having an issue getting the simple QSPI Peripheral example to show data consistency.
Can it...
Hello
I want to operate SSD1331 OLED(96*94) using sdk v17.0.2 and nrf52840 custom board.
The OLED example of sdk v15 was replaced with the codes of sdk17 and tested on...
Hi Nordic experts,
Recently, I consulted the datasheet and tried to find out something about the radio speed when using softdevice, unfortunately, I can't find anything...
We are in the initial stage of development of a product that will be shipped in different countries and different customers.
We would like to use an MFF1 or MFF2 eSIM for...
Hi
When trying to register iBasis sim with correct ICCID and PUK, I get this error message:
Username and pool information are required.
could You help me with...
I have my IMEI but my pin number has 4 digits: 0000, instead of 6 digits(which is required to add the LTE device)? Please Nordic, what should I do? I have this problem for...
I am a beginner in embedded systems.
I know that the minimum resolution of RTC is 1/32768, but what is the effective number of digits for this? For example, I used a counter...
I have not been able to confirm this from documentation. I need to know what the on/off and termination states of the nRF51822 GPIO pins are when the chip is initially powered...
Hello,
I'm using Segger with the nrf Connect SDK v1.5.1. Before my program's main even calls, the program is getting stuck in the nrf system calls; specifically nvmc_wait...
Hi, currently I am using fstorage alongside ble-mesh to store some data in flash. Currently however, writing with fstorage seems to be successful only about 50% of the time...
So , I have been fetching the customized packets through scanning . I managed to pickup the data from the structure
typedef struct { uint8_t *p_data; /**< Pointer to the...
Hello everyone,
I am using NRF52840 development kit. I am trying to migrate my developed code from SDK version 15.0.0 to SDK version 17.0.2.
While compiling the DFU firmware...
On the Android version of the application, Whenever a node is not the proxy node, you are unable to read the proxy state, get the ttl, and refresh the configuration server...
