I'm looking for a good firmware engineer that can take my current firmware and add the buttonless DFU to it. I currently use the Keil environment but am open to switching...
I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
hi , now I am using nrf52832 base on the sdk 14 to develop our location system, the ibeacon around my nrf52832 circuit board will advertise every 500ms, and the parameters...
My device is entering DFU mode, staying there for a few seconds, then shutting down. I'm trying to figure out a good way to figure out if it's a watchdog issue or a power...
Hi.. I am still new in using nrf product and understanding the example given via SDK. For my project, I am trying to send continous data via BLE app UART to mobile phone....
Hi,
As a part of settings up an automatic BLE DFU testing environment, we're trying to update a single NRF52 board using a PC connected to a NRF51 dongle.
The dongle is...
Hi,
I am using Sunding-515 cycling speed and cadence sensor it’s data is broadcasted as per the GATT characteristics. We have already done the data parsing in our other...
In SDK 15.0.0\modules\nrfx\soc\nrfx_irqs_nrf52810.h, at line 65,( link ) it defines a SPI1 compenent:
But 52810 spec( link ) mentions only SPI0.
Is the code file correct...
Hello everyone,
So I'm trying to maybe start get going with the NRF52832 platform but every time I try I get stuck with it.
In this example I'd like to use different...
Hello, I would like to know if there is there a "global" sdk_config.h file which has #defines for all modules? Ie, if I make my own project, and use this file, all I would...
Hi!
I would like create my own application of BLE Mesh on nRF52832, I had gone through the Light switch example and understood some basic concepts and now i'm thinking start...
Hi,
I tried to erase the bound and start another pairing procedure without rebooting my device. I was not able to remove the bond correctly. The system hangs when I call...
Hi,
I had Completed secure OTA in my custom board (RL nRf51822 A1).
We have to PCBs. 1). Old Design 2). New Design
1). Old Design: We have connected relay on pin(p6...
Hi all,
In our program calling app_usbd_cdc_acm_write() a single time does not directly send a message to the terminal program (Teraterm). Even Teraterm is not getting connected...
hi, everyone:
I want to use the experimental_bootloader_secure_serial to update firmware with UART, disable the hardware flow control.
how to reset system when application...
Hello,I have couple of nRF52832 boards,nrf5_SDK_for_Mesh_v0.9.2-Alpha.
I want to test the light control example,but some problem bother me.
It can not work normaly.The...
