Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hello, im relatively new to this and not sure why im getting this error. According to previous such error clarifications, i read that the newest versions have to be used....
Hi I have a couple of Thingy:91 devices, which we are using to evaluate the 9601 SoM.
The devices ran out of credit, but after buying more iBasis credit still would not...
Good afternoon. I use NRF 51822, and I want to use RTC 0 or RTC 1. But there are problems, if I do not initialize BLE then the compiler does not execute LFCLK_config because...
We are now developing BLE ADC sender, using nRF5_SDK_14.0.0_3bcc1f7, and two nRF528322s (sender and reciever).
We send SAADC data via BLE, after that, we disconnect, and...
I am currently using SysTick to count milliseconds in my device. This works fine, however with it enabled I can't sleep the device as it wakes up instantly.
I have tried...
Hi,
I'm not sure if I'm doing something wrong so I'm hoping someone can help me. After updating from 0.11.4 to 0.12.0 of pc-ble-python-py, I get the following error. I've...
Hi,
Please help to suggest if 10K Nodes in a single network with 100 Kbps data rate is achievable with data transmission interval being roughly every 30 seconds.
This...
I have the debug section of the evaluation board turned off, modifications to measure current with a DMM set up, and am using a keysight 34465a DMM to measure current. The...
Here is the code snippet initializing the Heart Rate Measurement Characteristic in the BleHeartRateMonitor example:
static uint32_t characteristic_init() { uint32_t error_code;...
When using nRF Connect and 52840 Dongle, the normal BLE scan app works fine but connecting to the RSSI ap, the reprogramming of the dongle fails with timeout.
Hi,
I have nrf9160 DK.
I found there is u-blox driver available. Is it possible that the 9160 modem can be added an interface as a modem using u-blox? If so, there is...
NRF_LOG_RAW_HEXDUMP_INFO() is not printing complete Extended Advertisement data in HEX format. It just prints first 80 bytes of whole advertisement packet.
I added below...
Hi Nordic Developers,
Service Discovery Protocol (SDP) is a protocol for Bluetooth to detect the service nearby and to determine their characteristics by using UUID.
I...
Hello!
I am trying to lower the sleep current of our custom board. Right now in sleep, the whole system have a current consumption of 100uA. There might be component choices...
