Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
How can application code interrogate the SD140 to identify which version (such as 6.0.0) is running.
We pre-flash (before SMT) our nRF52840 with a bootloader and SD140,...
Hi ,
What does the handle parameter in status_handle(access_model_handle_t handle, const access_message_rx_t * p_rx_msg, void * p_args)function (generic_onoff_client.c)...
Hi all,
I am trying to reduce the connection time between each connection to the minimal posible
Connect -->Transfer data -- Disconnect
I am facing two options...
Hi,
I want to make simple software that runs on PCA10056 using SEGGER and SDK. To learn how to use SEGGER, I copied exsamples / template_project and tried to imitate blinky...
Hello guys, i'm using nRF52832-DK with S132_v3.1.0 and SDK v12.2.0.
When other BLE device write some value to my characteristic, how do i know
that my characteristic...
Hello,
I am using a custom board that has a DSP and the Lairds BLE module BL651 that has nRF52810. I have written a simple program that sends a test data byte to the DSP...
I use nrf51422 dk, device: s310 2.0.1
Then i want to download "bootloader" from example floder by keil 4
but it can't work
and show up "JLinkARM.dll not found. please reinstall...
Hello,
I want to install nRF5x Command Line Tools on macOS, I found this user guide, infocenter.nordicsemi.com/.../nRF5x_Command_Line_Tools_v1.3.pdf and on page 5, it lists...
hello guys,
I using nrf52840 development kit and segger embedded studio. I want to write a program to implement spi protocol, can I get a simple reference code to write...
PWM output with stable frequency
SDK: 15.3.0 Example: low_power_pwm Device: EYSHJNZWZ (nRF52832)
I want to output PWM with a stable frequency. In the above sample, PWM...
Hi,
In order to speed up network registration times I'm trying to do a band lock to 13,4 (Verizon & ATT within USA), so I'm issuing the below AT command which responds with...
Hi,
The baseline PSM sleep current of our device with all of the additional support circuitry is 100uA, and have just integrated FOTA capability.
However when we set CONFIG_BOOTLOADER_MCUBOOT...
Hello! Trying to understand how to connect to AWS IoT. I use nRF9160. As for template I'm using mqtt_simple sample. I found broker address, but how to use security keys and...
Hi,
we user the standard NUS example as peripheral. Starting from IPhone 7 an mtu size of 251 is negotiated. Sending from the peripheral is possible but receiving from the...
