I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hi,
When using RTT for debugging on the nRF5340, after every flash i have to press the following button:
Then every time i get presented with the following dialog...
I would like to ensure that a particular GPIO pin is disconnected when an nRF52840 is powered up via the initial configuration specified in the DeviceTree board overlay file...
I get the following error when clicking flash button in nrfConnect VS Code extension with an nRF54L15 DK:
Error: One or more batch tasks failed: * 1057701224: Device error...
Dear Support Team!
I'm just about to flash an external board (nRF52820) through P19 where the MCU is powered at 2.3V. I would like to use the nRF52833_DK and the PPK2 to...
Hi Team,
We are using SDK 3.1.0 and radio FW version 1.3.7.
Trying to read RSSI, RSRP, RSRQ, SNR levels using AT command AT%MEAS but it returnns error.
Am I missing...
Hi Nordic,
I'm developing a BLE protocol on an nRF54L05, and is trying to send (On request or by notifying) up to 750 logs of data, each log being 8 bytes (1 byte event...
Hello everyone,
Im using nrf5340dk for the first time, i have built project for nrf5340dk_cpuapp and i think code is good but for some reasone i dont see a led diodes turnin...
Hello,
I had a question about the BT GATT DM Workqueue used in gatt_dm.c.
In NCS 2.8.0, the BT GATT DM Workqueue was introduced as an alternative to the System Workqueue...
Hi List, I have been successful to run my basic functionalities like GPIOs, I2C and ADC using custom board files for nrf54l15 based custom hardware.
Now, I am trying to...
Description:
Hello, We are developing a DECT NR+ communication setup using multiple nRF9161 DK boards arranged in a Sink–Relay–Leaf topology.
Each board operates as a...
While working on debugging our application firmware using the nRF9151, we ran into issues that we hypothesized as being caused by an incorrect modem clock leading to validation...
Hi Nordic team, We have a production firmware developed on nRF Connect SDK v1.7.0 targeting a Fanstel BLG840FB4 gateway module (nRF9160 SiP + nRF52840 SoC). We are trying...
