Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Did anyone manage to build project on Eclipse with some nRF52 BLE application for HomeKit?
I have found only one project from aanon4 but I cannot even build it.
Sometimes...
Hello,
I am thinking of creating a project that I intend to manufacture that needs to operate 10 dc motors via Bluetooth.
Would this be a logical and cost effective...
I am using nrf51822, I have two firmwares with different offset address, one is having offset address of 0x16000 another at 0x28000.Both are 60kb of size each. I want to start...
Hello all,
I try to find out how long some configurations of the Enhanced Shock Burst protocol take time. I am working with the nRF52 Development Kits.
Some timings...
I want to combine two applications, both of them having two services. One application resides at 0x16000 and other one resides at 0x249f0. I am using softdevice 7.3 and sdk...
I am using nrf51822 and softdevice 7.3. I am working on the github mesh example. I want to add uart service with mesh, so that I can communicate with that particular device...
Hello, this is what I can think of when porting a project, but before that, a little background about my project:
it uses BLE (duh)
it uses uart to print test output...
Hello,
i am using the nRF52 Development Board with SDK 11 and I have trubble with the UARTE Interface with DMA. Parallel I have running the ESB protocol.
I know the problems...
hello there i want to add battery service and thermometer service in advertisement packet. so i changed in uart project. but in advertisement project i can see battery service...
hi
I used the nrf51 dongle to receive advertisement packet from other nrf51 dongle. I used this formule, d = 10 ^ ((TxPower - RSSI) / 20) , given from this link forums...
Using Command Line Tools 9.0.0 attempting to push code.
ERROR: JLinkARM DLL reported an error. Try again. If error condition
ERROR: persists, run the same command again...
Hi All,
I am attempting to use 6 PWM channels with the app_pwm library on the nRF52 and am only able to successfully get 4 pwm outputs. Upon changing the 6th channel (PWM2...
I need 3 time aligned PWM channels (period of all three channels needs to start at the same time) at about 100 Hz with 16 bit resolution on the duty cycle. I also need to...
hello,
I used nrf52 and softdevice 2.0.1 and i have a big problem.
For some times the BT works perfectly but after i connect more then 4 devices for some reason
the...
Hi,
I need to check the emission of my custom nrf52832 board design and I need an spectrum analyzer... To see if my design would pass the regulations and tests.
I was...
