Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
We are working on the nrf5340 and our current device firmware uses the NCS 3.0.2 (i.e. nRF Connect SDK 3.0.2). We wanted to try an upgrade to NCS 3.2.1 and followed...
Hi, so my intention was to test the free subscription of Memfault with the thingy91 I created my account in nRF Cloud but the button to access Memfault is not there, I had...
In the documentation , it is stated:
The SAADC is preceded by a gain stage which has a programmable gain. The voltage range seen at the input of the gain stage is:
...
Hi,
We’re looking for the SBOM and the official CPE identifier for the Nordic nRF5 SDK, specifically version 15.3.
We would need:
The SBOM for nRF5 SDK v15.3
The...
I am using the nRF52840DK with nRFConnect for VS Code. In Lesson 6 Exercise 1, I connected the DK to a BME280 board I purchased online. The board exposes the four pins needed...
I've been wrestling with an issue whereby I attempt to deploy an mcuboot image to a device and inconsistently I get a message that says the firmware image is not valid (error...
I am currently encountering an issue with BLE bonding logic in my application.
When a phone initiates a pairing request and triggers a pairing pop-up, I use the security_changed...
We have a custom PCB with a nRF9151 implementation supporting both LTE/NB-IoT and GNSS. The PCB has no switching regulators or any other possible noise source except for the...
Working the SDK intermediate course, L1.E1. (SDK 3.2.1 / nRF54LM20A)
After building, I select <Debug> under Actions in VS Code. I get this popup that says "Debug options...
Hi DevZone Community,
I am facing a build issue while working with the following environment:
Environment
SDK: nRF Connect SDK v1.9.1
Hardware: nRF9160 DK...
Hi,
As the subject states.
I would like to run the tests at zephyr/tests/drivers/spi/spi_controller_peripheral as intended in testcase.yml. I can verify that I have the...
Hi All,
Anyone has experience in FRAM?
I have a project which need to integrate the FRAM CY15B108QN with nRF52840. I got a weird result by using nRF silicone, but can...
Hi,
I wanted to use the `nordic-semiconductor.nrf-kconfig` and the `nordic-semiconductor.nrf-devicetree` without the nRF Connect extension in `vscode`, but they don't seem...
Hello, I am an absolute beginner with nRF9160. I have just received one development kit.
I am trying the Quick Start application for cellular modem with AT commands.
Unfortunately...
Dear Nordic
At ncs3.2.0 zephyr sample, we found uvc sample as below.
https://docs.nordicsemi.com/bundle/ncs-3.2.0/page/zephyr/samples/subsys/usb/uvc/README.html#uvc
...
