Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Looking at
\NORDIC\SDK\examples\peripheral\spi\pca10040\blank\config\sdk_config.h
These lines repeat over and over. Was there a reason for this? The first time the infdef...
I just nRFConnect to find the JLink on a Mac. JLink is connect to the devkit, a BLE400. As soon as I select the com port, nRF Connect asks me if i want to install the latest...
I was wondering what material was used for the Thingy52. I'm guessing the top was some type of cast silicone while the bottom is some type of PC. Part numbers of the exact...
Hi, I just want to know,
Is it possible to develop a device that advertise normally and be connected by mobile, but the device must always send the eddystone-format advertising...
Hi,
I wonder what transfer speed can be expected on a BLE DFU update on a nRF52832 based device in the following condition?
-SDK14.0 Secure DFU, nRF52832, Android tablet...
I get an app error SOFTDEVICE: INVALID MEMORY ACCES if I try to write/clear RESETREAS after the softdevice has been enabled.
Why is this happening?
You can reproduce...
Hi
I'm using a nRF52832 togehter with the SoftDevice SD132 and the SDK V12.2.0. I encounter the problem, that the SoftDevice runs into the softdevice_fault_handler(). The...
Hi,
I'm using the ble_app_multilink_central example in the newist SDK nRF5_SDK_12.1.0_0d23e2a, nRF52832. Now it can printf the log information. I want to use the uart to...
Hi,
How to interface UART between NRF51822QFAC and LPC1769, which tool can used for NRF51822QFAC and how to compile the source code, please send me download path for tools...
I'm observing frequent Bluetooth disconnection on my custom board which has nRF51822 SoC.
So far, I haven't been able to figure out the root cause. In order to narrow down...
Hi there,
I am currently runnning tests with the nrf52840 for university project on Bluetooth 5 and I'm struggling to figure otu how to change the PHY used,
e.g. in...
Hello together,
i know, there are similar questions about "Reading Characteristic Value", but i don't get a solution for me. My Problem:
I use nRF51DK with SD130 and the...
Does the aplication nrf connect work in win10?
on Bluetooth low energie app ckliking on "server Setup" nothing happens and "start scan" is always unselected,
computer...
Hey,
I was researching on whether the advertisement period ie the time for which the nrf advertises (tWA in figure) can be changed after each advertisement interval(tAI...
