Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
Hello,
I want to store temperature samples in flash of nrf51822. I am using pca10028 and sdk 12.2.0.
I have the code for writing,deleting and reading from flash memory....
Hello,
I have a question about stack usage. I use nRF51822 SoC, 12.2 SDK & IAR 7.60.1. I am interested in stack usage. Have you done any estimations? Or may be you have...
Hello, I get the
"ERROR: The --family option given with the command (or the default from nrfjprog. ini)
ERROR: does not match the device connected."
message after...
Good morning,
this is Algocraft (www.algocraft.com), an high tech company whose core business is to develop, design and market a wide range of professional systems dedicated...
I'm using
SDK : nRF5_SDK_17.0.2
Example Project : ble_app_uart
Soft device :S113
The initial project builds successfully.
The example provided for ble_peripheral...
Using SDK 17
There must be a way to show all commands in RTT without needing the tab to work right?
Ive been digging through the code but don't see where the magic happens...
Hi, when i'm debugging my circuit, the logical of a if or while don't work. In the image, the timeout_rtc is higher than 100, but the value of a don't change to 1. What's...
I used the P1.13 pin of NRF52833 as the output pin, and used it in the manner of the blinky sample program, but it crashed and prompted the following error message:
***...
Hello, I have a custom HOST board. There are use NRF52840 BLE chip.
I'm run Bluez 5.61 on the HOST board and by meshctl> I am able to run as a controller. But if I want...
how to set BLE_GAP_ADDR_TYPE_ANONYMOUS
i have follwoed https://devzone.nordicsemi.com/nordic/short-range-guides/b/bluetooth-low-energy/posts/ble-advertising-a-beginners...
Hi,
There are tons of documentation on how to make a mouse, keyboard or remote control work as a HOGP device, and I have successfully implemented both mouse and remote control...
Hi,
Using NRF Connect 1.6.1 on NRF5340 I have modified hci_rpmsg project to add another endpoint for bidirectional calling between app core and net core. I have used the...
Is there a reason that AT_CLIENT example always works for LTE but SERIAL_LTE_MODEM only works the first time, and then trying again it never connects to the LTE ? Typing AT...
I’m trying to write a program that reads data from 4 hall effect sensors and outputs it to a serial monitor over Bluetooth. The sensors communicate over I2C. The programs...
Hello,
I've purchased the nRF52840 Dongle: https://www.nordicsemi.com/Products/Development-hardware/nRF52840-Dongle . I've successfully flashed it with the version 4.0...
Hi：
I use nrf52832 to connect to the sensor module through uart. When the sensor device is turned off, I can repeat the pairing and unpairing of the Ble module through the...
Hello,
After reading many things, I would like someone to confirm or correct my understanding. I believe this will be great clarity for others as well.
The nrf52 requires...
Hello dear all. I am compiling a firmware to merge the timer function into the nrf52-ble-app-uart-c-multilink firmware. The timer function is copied from ble_app_uart__saadc_timer_driven__scan_mode...
Hi,
I am a new beginner when it comes to Thread and Matter. I am trying to run Matter on nrf52840. I flashed the door lock example, commissioned the device using BLE and...
