As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hello,
I am using nRF52840, SDK16 & SoftDevice140.
I am integrating pm_init()(Peer Manager) into my project and I am getting error 0xFFFFB180 from mbedtls_ecp_gen_keypair...
Hello,
We are using the nRF52 DK board and Keil uvision 5.
Using SDK 17.0.0 we can successfully load and build the `examples`. If we choose `examples/peripherals` we can...
Hello, everyone.
I would like to use LSM9DS1, a 9-axis IMU sensor. To test this, an IMU sensor module 'SparkFun 9DoF IMU Breakout - LSM9DS1' was purchased.
This module...
I am working with Zephyr version 2.4 on nRF52840-Dongle for adding ability to scan CODED PHY devices. My host is Raspberry Pi3 with kernel version 5.4.51 v7+, HCI_USB sample...
Hello,
I am trying to run USBD_MSC example using PCA10056 board from SDK15.
It works fine, when creating new file on each button press.
I modified code to create and...
Hello everyone ,
I have question about the difference between periodic message publishing via the module's configuration and publish message by a standard timer.
I notice...
nRF52833 DK i have seen from Images of board that an external antenna will be required(there is a Antenna connector on board). I am wondering if it has built-in antenna or...
Hello,
I am on nrf-sdk v1.3.0 and mwf v1.2.0.
We are updating our product to the above mentioned nrf-sfk version and have noticed that MQTT connection gets stuck after...
Hi,
I enabled flash log backend with NRF_LOG_BACKEND_FLASH_ENABLED set to 1, and NRF_LOG_BACKEND_FLASH_START_PAGE to custom address to keep it as the starting address for...
Hi,
We have successfully created a PCB layout with a PCB antenna following the reference schematic provided by the nrf8001 datasheet. We tested and it is working fine. However...
Hi,
I am trying to interface External Flash (IS25LP064A ) using SPI example in SDK v16. I am able to read the Manufacturer_ID and the device ID from the external flash....
Hi,
Is it possible to somehow read END event register via CPU (not with ppi usage)? If yes, how? I have tried to read value on address from pointer returned from function...
Hi, I am facing an issue my product contains Ble dfu update, I tested my code without enabling DFU and it runs fine ... but after enabling dfu and creating package... I update...
Hello, everyone!
I use SDK v17 and test various functions using App_Timer. The timer function that I want is to turn the LED on for 5 seconds and then turn off after 5...
Hi,
We have been working with a coordinator and an end device based on nRF52840 with nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b
Both devices are Zigbee 3.0 and implement...
