Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hello,
We decided to use the 802540 battery for our application with the nPM1300. To get a good estimate of the state of charge (SOC), we did the very lengthy battery profiling...
Greetings
I am looking for a conceptual guide to adding my own services to the BLE stack, with Zephyr. Is there any documentation or guide for this? I am working on the...
Hello, I am having an issue with DSP library basicmath where the source file does not seem to be included in the build and I am getting error undefined reference to `zdsp_mult_f32...
Hi,
I am using nrf5340 with v2.5.1 toolchain
I have an out-of-tree driver, where i want to include adc_context.h from and have added:
target_include_directories...
Hi I'm trying estimate the nRF52840s current with the Online Power profiler, the data seemed a bit unclear to me.
I have used the following setting: Chip nFR53840 Voltage...
Hello,
I am trying to do CE, FCC RF test.
I am using nRF52833 and nRF5_SDK_17.0.2_d674dde.
I want DTM to work. DTM is using example source in SDK. What changed in...
I am trying to develop a Consumer Control device. I found the "nrf51_ble_app_hids_kbd_consumercontrol-SDK15" example code on Devzone. But this example code can only do 8 Consumer...
Hi, I have been using nrf52840(my application) and nrf9160(Serial LTE Modem : SLM , which modem firmware was ver1.3.6 and application firmware from switch science )
First...
I tested the matter LOCK sample, how to disconnect the Bluetooth connection immediately after matter commissioning is completed, the log is as follows. thanks.
Hi, I am currently evaluating a Rust driver for the nrf7002-ek on a nrf5340-dk. I have been using the Zephyr nrfwifi driver for reference.
There are a large number of nrf_wifi_fmac...
When building a project using a custom board, as well as both the b0 and mcuboot bootloaders enabled, board-specific child image configuration causes the build system to ignore...
Hi All, I am looking for assistance with trying to reduce flash usage of my project. I am using NCS v2.6 with an nRF52832. Attached is my prj.conf file. The major SDK features...
Hello, I'm working on a Zigbee application using the nRF5 SDK for Thread and Zigbee v4.2.0. The app builds fine, but when running it I get the following output:
I have...
Hi All,
We are developing a heater controller using Nordic Matter Thermostat sample code. The sample code has following value.
Off
Heating set point
Cooling set...
Hi,
I use 3 devices in the Mesh application. I am looking at the Mesh:chat example. I want this,
I want to press a button on one device and light LED1 on other devices...
