Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
hello, there my application is like that...
(1) calculate size of receive buffer. than read that size of data.
again new data comes, then again calculate that size of...
Issue: With my external antenna design, I get lower dbm than PCB antenna (nRF51DK) with same distance.
My external antenna design: -70dbm
nRF51DK: -40dbm
In this...
Today when I started power profiler kit, it suddenly started to show peak values like 80 mA. This has not happened before, but the values with the same hardware have been...
In the data sheet of the NRF51 and 52 there is mention that sensitivity of NRF51 is -96 dBm and NRF52 -98.
But I read some where that when RSSI is -90 then that signal...
We are working on a dynamic radio power change for a proprietary RF protocol, and we are missing some granularity on the NRF_RADIO->POWER levels.
Typically we would need...
I am wondering what is the logic and magic behind using sdk API's to advertise vendor specific 128-bit service UUIDs. In the "Nordic UART Service" example (nus, SDK12.2.0...
Hello all!
We are designing our first projects with NRF52832 and the DC-DC decoupling capacitor on DEC4 pin used in reference design is:
1uF 0603 X7R 16 Volts
Our...
Hi
Now I'm using sdkv12.2 and S132 on nRF52832. All the examples in the SDK put the device name in the advertising data packet. However, for our applicaiton, we need to...
we have created ble mesh, and data through ble nodes is passed every 5 seconds, but nodes gets disconnected with reason BLE_HCI_STATUS_CODE_LMP_RESPONSE_TIMEOUT??
please...
For a moment I was thinking that I made it with Segger, I was thinking that after 3 days with Eclipse with no success, I managed to use the blinky example and flash it (!...
Hi.
I'v spent the last full days trying to set this up, and I am exhausted. I really am. Never had this kind of feeling in my life.
People from all over this place where...
Hello, the nrfTooolbox app from Play Store runs on my LG K4 phone which has 5.1.1 Lolipop. If I load the Github project into my Android Studio and try to run it on the phone...
Dears,
I am working for an application on [email protected] including PWM, Timer and a few peripheral functions. I was trying to create a timer on timer1 in us tick. The timer...
The UART example in examples\ble_peripheral\ble_app_uart will not connect with SDK 13.0.0. This example was running just fine with v11.0.0 (Softdevice S132 v2.0.0) and v12...
