Using nrf sample from v2.9.1/nrf/samples/crpyto/rng Configure build with v2.9.1 SDK/Toolchain Configure build with board target: nrf5340dk/nrf5340/cpuapp Add MCUBOOT support...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hello,
I am currently using nordic connect sdk version v3.0.2 which seems to be the latest release on github. I am using https client example. As per the requirements...
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi,
I made a custom board with nRF54L15. I do not have a spectrum analyzer, so I cannot tune how much power goes to the antenna or how much is radiated. So, I started ADV...
Hello -
We are working with a custom board that is similar to the SparkFun Pro nRF52840 Mini . We are using the nRF52840 SDK version 16.0.0 and SoftDevice 6.1.1. Our board...
Hi everyone.
I am working on the ble_app_bps_pca10056_s140 example. I want to confirm that a BLE event is received when the APP_ADV_DURATION has been expired.
After searching...
Hi,
I noted that the CW generated in the %XRFTEST TX test seems to be offset from the requested frequency. Specifically, issuing the command
AT%XRFTEST=1,1,20,8500,-50...
Is there still no way on this build to setup zerocrossing detection?, I mean using interrupts I developed a zigbee dimmer that detects zero crossing and dims 3 separate channels...
Hi,
We are using NRF52840 Dk board to transfer the data at 10ms through Bluetooth which is central and peripheral as other cc250moda controller Bluetooth. Our objective...
Hello:
I am porting the LESC with MITM security protocol from your "ble_app_multirole_lesc" example inyo a project that runs FreeRTOS. This is on an NRF32540 With s140...
Hi,
I'm using an nrf52840 dk to query another device over spi and then pipe the response back USB to a host PC. Ideally, we're piping data at 1 Mbps (which should be very...
Hi,
We are using nRF9160 DK. Loaded the asset tracking application, and followed all the procedure to connect to nRF cloud.
In nRF cloud i can see the data in the cloud...
Hello,
I am currently designing a custom PCB with the nRF8001 chip. For a smoother assembly and component procurement, I am looking to make all the resistors on the board...
Hi there,
I have a problem with the bootloader from the RF5_SDK_11.0.0_89a8197 together with Intel Wireless Bluetooth chipset.
I use the softdevice s132_nrf52_2.0..1. I have...
Hi im after the library driver for the nRF509 using Arduino but when i go to the webpage to get it the webpage says not available can someone advise please
Many thanks ...
Hello,
Is it correct, that periodic advertising is working only with non-connectable mode? To implement periodic advertising with connected mode I need to start the second...
Hi, I tested a simple client-server UDP application, using as a template the UDP examples from the SDK. The UDP server is running in a nRF52 board and the client is a Python...
Hi,
my goal is to send data to the Google Cloud Platform using CoAP.
I found this example:
https://infocenter.nordicsemi.com/topic/sdk_tz_v3.1.0/thread_google_iot_coap...
