I will attach my main.c and skd_conifg, maybe i'm overseeing something in code. Also i will attach schematics and pcb. I'm aware of RGB led consumption, in reality it's around...
Dear Nordic Support Team,
We are in the process of integrating the Nordic nRF Mesh SDK (version 3.3.4) into our custom Java-based application and require your guidance on...
NCS 2.9.1
NRF52840
Sysbuild but with only a single image (no bootloader)
I've been trying to figure out how to change the merged.hex output and how to perform additional...
This stopped working for me... Error is the following
Command failed: git ls-remote --tags --heads github.com/.../sdk-nrf
fatal: unable to access ' github.com/.../'...
Hello,
After a lot of efforts I managed to autoprovision and autoconfigure my nrf52840 board (provisioning and configuring inside the software and not through external app...
When version 1.0.0 of nRF54L15-DK evaluation kit will be available and how to distinguish the version when ordered from distributors like Digikey?
In discussion here:
...
-> How to transfer data from one thingy52 device to another thingy52 device. If i have 2 thingy52 devices, I'll send data to 1st tingy52 then 1st thingy52 device will send...
Hi Sir,
According to the datasheet of 52840 (v1.1), in the ref. schematic, the requirement of 32M is +/- 40 ppm.
In section 5.4.4.2, for the frequency tolerance requirement...
Hello,
Please comment on the expected difference in achievable range using 20 dBm vs. 23 dBm output power. Any details, assumptions, questions, etc. would be appreciated...
Hi, I'm looking for a more modern transceiver than nRF24L01 + and that works for the same. I am looking for a low or ultra low power transceiver that allows the implementation...
Hi, For my POC I use nrf9160 dk. Nrf52840 is used for scanning ble devices and nrf9160 dk is used for sending data to mqtt server (very similiar to one of the examples with...
Hello there!
We would like to use INT1 pin of ADX362 low power accelerometer on Thingy:91 board to interrupt nRF9160 (e.g. wake it up) when some motion is detected.
To...
Hello,
I am currently designing a new board using the nRF9160 chip and looking for an alternative component to use instead of the GPS RF Amplifier QM14501 and RF Switch...
I need to exchange data between nrf52840 and Linux PC. I see example project in nrf5SDK/examples/peripheral/usbd
Can anybody advise any example project for Linux C/C++ to...
Hi,
I'm working on nrf52840. As far as I understand, that device supports connection to peers with BLE 4.2 at least.
However, I'm able to connect via my phone, which...
Hi,
I have some questions regarding the state of the GPS functionality, and the future plans for nrf9160.
Will continuous GPS tracking while simultaneously using LTE...
Hi,
We are working with DK nrf 52840 and developing android app with nrf mesh library. is there a way to receive the feedbacks to the provisioners when any generic clients...
Hi ,
1-) Is there any dma half transfer interrupt ? if there is where it is in documents ? ( i check this link but i couldnt see anything about this https://infocenter.nordicsemi...
It is pretty straight-forward to use J-Link RTT Viewer on Windows (as described in the Debugging with Real Time Terminal tutorial ). Is there a similar viewer to use with...
Hi,
I am designing a bio-signal measurement circuit using nrf52832.
I wonder if there is any problem with the performance of nrf52 when using the sensor below.
Sensor1...
I can't comment in https://devzone.nordicsemi.com/f/nordic-q-a/56685/missing-ble_gatts_evt_hvn_tx_complete-events as it is closed but I am also seeing issues with the TX_COMPLETE...
Could you display on the ticket list page also when the ticket was last updated?
Now it shows only creation date, but I do not see indication which one was recently updated...
