Hi:
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party repository within the SDK itself...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
We are using SoftDevice: sd132 v 5.0.
With event "BLE_GATTS_EVT_EXCHANGE_MTU_REQUEST", the function "sd_ble_gatts_exchange_mtu_reply" always return with "NRF_ERROR_INVALID_STATE...
I am using Fansttel BT832X SoC with SDK 14.2 ( Soft Device Version S132 5.0 ). i have configured PA/LNA mode in BT832X module. If i use only BLE advertisement i can see the...
Hi,
We want to update nrf52832 via uart. We have host controller and want to upgrade nrf52832 through it. We have SDK BLE_2.0.1 for the mesh. I had gone through DFU Example...
Hey,
I have a smart kettle Redmond RK-g201s, which is controlled by bluetooth. I have read that it has nrf51 SoC. It has 1 service with 2 characteristics: for read and for...
Hi Nordic:
I want to consult one question about "BLE HID Keyboard". I am trying to use the product---nRF52832 to make the "BLE HID Keyboard".
Then I download the source...
Hello Nordic Team,
I have some issues with the PPK since i uptdated nrfconnect from 2.0 to 2.4.
I get this error message when I try to select the serial port on Power...
I have some working knowledge of Android but I'm new to Fragments, Injection, Binding, ButterKnife .etc. I have gone through some videos and tutorials but can't catch where...
Hi,
I am using the nRF52832 DK for connecting and collecting the data from multiple beacons simultaneously. Right now i use the nRF_Connect desktop application for collecting...
Hi,
We have a nRF51822 project based on ble_app_hids_keyboard, SDK 12.3. When using Keil, it runs well. However, when using arm-gcc to compile the same code, something wrong...
Hi,
I am currently exploring the USB_CDC_ACM examples as well as the NFC record launch app.
Individually, I can make the examples run fine.
Then, I tried to combine...
Using nRF52840 SDK 15.0.0 with SoftDevice
I am trying to protect the Access Port, used to do it using the following command
nrf_nvmc_write_word(NRF_UICR->APPROTECT, 0xFFFFFF00...
Hi,
I'm using the NRF52840 SDK version V15. My program uses:
1. softdevice (BLE communication)
2. SPI uses using SPIM interface in nonblocking mode.
3. Timer event...
I am trying use DFU example with Mesh sdk 1.0.1, however following the start DFU guide, i have some question, if i have two DK52 one of them must be programmed with the original...
Hello,
I want to use privacy (BLE_GAP_ADDR_TYPE_RANDOM_PRIVATE_RESOLVABLE) if the connected device support this feature. As far as i know it's not possible at application...