Hi,
I ran into this error:
00> <error> nrf_ble_gq: SD GATT procedure (1) failed on connection handle 0 with error: 0x00000008. 00> 00> <error> app: ERROR 8 [NRF_ERROR_INVALID_STATE...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Hello,
I know this question is more related to Zephyr than Nordic, but I wanted to try asking here.
I’m using the SMP service to send files to my device on a LittleFS...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
Hello Nordic team,
I've recently upgraded my application from nRF Connect SDK v2.7.0 to v2.8.0 , and the previous BLE Disconnect issue has been resolved — thanks again for...
I have a smartwatch, smartphone, and tablet.
I went to some place without any other bluetooth devices, my devices are able to scan and pair with each other. But nRF-51 not...
Hi,
I have followed sequence in http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.0.0%2Fsdk_app_serial_dfu_bootloader.html&cp=4_0_0_4_3_4...
Hi,
I have a beacon code for nrf51 that I wanted to port to nrf52. It uses app_timer, gpiote and adc. The power consumption in idle is ~30uA. Now I wanted to port this code...
FDS_VIRTUAL_PAGE_SIZE
The size of a virtual flash page.
Expressed in number of 4-byte words. By default, a virtual page is the same size as a physical page....
Hello,
I would like to use proxy_server(example of light_switch ) and ble_app_blinky_c, to make these two functions work together in one card. So this card can be controlled...
Hello everybody,
i have crated an Report id for the telephony usage on iOS from here https://opensource.apple.com/source/IOHIDFamily/IOHIDFamily-247/IOHIDFamily/IOHIDUsageTables...
Hello All,
I'm trying to program a NRF51822 module for the first time.Using Keil, Soft device s110_nrf51_8.0.0,soft device kit nRF51_SDK_9.0.0_2e23562 when I try to program...
I found the next response in a topic and i would like to know if there are some new improvements in the last SDK mesh 2.01.
devzone.nordicsemi.com/.../120547
I turn off...
I have installed from "nrfgostudio_win-64_1.21.2_installer" on Win-10 laptop. Weh I start nRFgoStudio, the main window appears for a second then I get a message "nrfgostudio...
Hi all, we're using code from this forum to enable GPIOTE and PPI to measure the low between the arrows to indicate a "start of transmission" and then switch to measuring...
Materiel and software use :
SDK mesh 2.0.0
SDK 15.0.0
NRF52832 with PCA10040 x5
Situation :
I would like to implement this network :
I follow the instruction...
I'm using the UARTE peripheral via the UART driver code in SDK v14.2. Due to transfer size and SoftDevice timing I have to use the double-buffered receive method (by calling...
Hello,
I am trying to make a beacon start advertising on a long press of a button. Using this as a reference, I implemented a timer as follows:
this is the flag to keep...
Hi!
I am using SDK15, my application is based on app_ble_uart. I have added my proprietary characteristic to NUS next to RX and TX Characteristic with quite a success. Now...
I use sdk14.2 nrf52832 as the primary, connect two iphone peripherals, iphone is connected to broadcast, when I turn on both peripherals, sometimes everything is normal, sometimes...