Hi. i'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
I want to make sure that how to operate DFU.
Please check there is missing point or wrong point.
Step 1...
Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi,
NRF52840 datasheet section "5.4.4.2 64 MHz crystal oscillator (HFXO)" mentions crystal tolerances being dependent on packet size.
It is not clear to me, what layer...
Hi,
I've had the nRF52 and Segger Embedded Studio on my old computer. But the old computer is dead now.
I am trying to create the same environment on my new computer....
Hi nordic
I run the HID keyboard with SDK 15.2 and connected to IOS's nrf conncet.
but i can't see the HID service in the table.
how can i use the nrf connect to debug...
Hello there,
I'm ripping my hair out hear reading everything I can to get the non volatile memory reading and writing.
I have a nFR52840 dongle and I dont want to...
Hi everyone,
I have a project that needs to use multiple saadc channels but I don't want to use ppi but use app_timer. So is there any way I can change between saadc channels...
I'm using a timer to trigger pins via PPI & GPIOTE. Setting the PPI TEP to the GPIOTE task works as expected. However, when I try to set a second pin via GPIOTE task via PPI...
hello Nordic
i am working with nrf52832 soc with SDK 16.0, S132 V7.0.1
following this path:
https://devzone.nordicsemi.com/nordic/short-range-guides/b/software-development...
Hey,
There is a microSD connector on the bottom of the nRF9160DK (v.1.0.2). Is there a way to utilize it as an external memory? I can't find any information about it on...
Hello,
I've been studying Bluetooth technology for a few weeks. I wanted my first to implement a simple key finder device, as my first project. I was doing some research...
Hello, For our nrf52832 custom board developed using nrf SDK 14.2, I need to turn OFF and ON LED accurately in terms of ms, hence after going through this page, I used Single...
Hi,
We are developing a device that should work in multiple mobile networks, and some of these are known to provide no DNS server. As using a fixed IP address for our cloud...
Hi,
I want to read the data from the a cceleration sensor by I2C. Several days ago, I added the code about twi bus to "ble_app_template" example , it worked well. But today...
I have a custom board, I am using to evaluate nrF52811 from eclipse (I just prefer this over SES).
I have installed S112 on the flash and also my application at 0x19000...
I'm communicating with N25 flash memory, the page size is 256 bytes. there is a page_program command which can write up to 256 bytes. there is no way to write in the middle...
Hi I'm trying to change peripheral usbd_ble_uart_freertos example to central with nus_c I added the scan and nuc_c module. When I'm testing the application, before making...
