i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hi, looks like I brick my nRF52840-DK board.
It have no any green lights anymore and even do not detected as USB device. The second device I have works well in the same...
Is Thread in nRF Connect SDK developed based on Zephyr RTOS？Do I need to learn Zephyr RTOS to develop Thread using nRF Connect SDK? I just started learning Thread。
Hi,
I am currently evaluating BLE long range feature for one of the our product. for this, using two nRF52840 dongle PCA10059. One used for peripheral and another for central...
Using Zephyr, I'm looking to configure the BLE name of my devices to use the serial number they are provisioned with.
To this end there is the API "bt_set_name" that seems...
Hi,
I have a firmware which need to transit to System-OFF under certain conditions. The startup code of the firmware enables the watchdog timer, which can't be disable...
Hi.
i see that ther are democode in zephyr that use the can shield DFRobot CAN bus V2.0
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.7.1/zephyr/samples/drivers...
Thanks in advance for the help.
I connected my 9160DK (V1.0.1), loaded Asset Tracker V2, etc., and seem to be connected to nrfCloud fine.
I don't seem to ever receive...
Hello all,
I am trying to on implement a custom 802.15.4 implementation (not thread nor zigbee) from the nrfxlib 802.15.4 radio driver in NCS. The goal is to run it in...
Hi, I have this weird issue with the USB behaviour of some of our pre-production units.
2 boards with USB came out of the oven and their USB was working fine. I was able...
HI Devzone
currently my customer would like to get SRAM execution permission in their porject.
we found a config marco to set the SRAM permission " CONFIG_SRAM _REGION_PERMISSIONS...
HI,
i using 52840DK SDK17.2 s140 10056 test NFC pairing.
ble_central\experimental\ble_nfc_pairing_reference_c 10056 s140 ble_peripheral\experimental\ble_nfc_pairing_reference...
I am using
MF V1.3
NCS V1.6.0
nRF9160Dk V0.15.0
Project: AGPS Sample
If i set the Interval in the gps_config structure to any number under 240 and run the sample...
Hi,
We are working on nrf52840 in that we have some doubt how to test the radio tx and rx in datasheet you have mentioned
Active mode Tx Current - 4.8mA and 0dbm ...
Upgraded from v16.0.0 to v17.1.0 and have a truncation issue. It only occurs after the first send. Reverted back to v16.0.0 and all ok.
No other code change other than the...
I've searched around, but i couldn't find anything about how to use DMA with SPI master on a nRF5340 (and zephyr doesn't support DMA on nRF5340 right?). Can someone point...
