We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
Is there an AT command (For modem firmware >= 2.0.2) that can be used to validate whether the LTE modem can communicate with an external MIPI RFFE switch (for example on a...
Hi ,
1.In the example: In nRF5_SDK_17.1.0_ddde560_usbd_msc_1\components\libraries\block_dev\qspi\nrf_block_dev_qspi.c, I need to set the following 0xB7 bytes. How should...
I have a project that I need to use most of the GPIO pins available on the nRF52840 DK. I'm using SDK V17.
I'm writing a test program that toggles all GPIO pins on an nRF52840...
Due to production requirements, I need to obtain the device's QR code. However, I found that the QR code can only be retrieved using the code snippet below after calling Nrf...
Hello everybody,
I am trying to get the RTC0 peripheral working on Nordic nrf9151-DK using libraries from Nordic (nrfx_rtc.h, nrfx_clock.h and hal/nrf_rtc.h). I am not...
Hello everybody,
I am trying to get the RTC0 peripheral working on Nordic nrf9151-DK. I wanna use zephyr/driver_rtc.h library and zephyr/device.h librrary. I am able to...
Hi, We are trying to get our nRF54L15 running, but are running into clock issues. The hardware is configured without an external 32kHz crystal, so we want to rely on the NRF54...
Hi, The Kconfig fragment CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU is awesome to quickly get BLE OTA working. However, when going in depth, we can see that it's implying:
...
I'm developing my application with nrf 52832 and nrf SDK v17.
I know NCS is more powerful. I'm currently learning how to use it.
But now.I still need my application with...
I'm developing with an NRF52832, using NCS v2.6.1/Zephyr 3.5.99
My custom hardware has three NXP PCA9538 GPIO expanders on it, to allow me to control various address and...
Is there any documentation around the process to disable the Debug Access Port on a nRF54L device in software (not nrfutil)?
The nRF52840 has this nice documentation page...
Hi
I can run the sample application for NVS, on the nF5340 DK (SDK 2.9.0)
I can run the sample application for LittleFS, also on the nRF5340 DK
Now I would like to see...
I am using nRF52840dongle and trying to flash the Blinky sample application provided in Zephyr.
Blinky: docs.zephyrproject.org/.../README.html
I had referred the programming...
Hi,
We are working with a custom board that uses the nRF54L15 and I seem to be getting a lot of errors (but not always) related to memory access error when flashing the...
