I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
We are currently experiencing malfunction with the big chip on nRF9160dk board, which provides USB-UART and jLink functionality. After 30 minutes, to a few hours, we either...
I have nrf52832 dk. I used power down example by github
https://github.com/NordicPlayground/nrf51-powerdown-examples : system off wakeup on gpio. Upon current measuement...
Hi Nordic Engineers,
I have few queries over HFCLK 16 MHz timer.
I am using nrf52840 custom board. IDE - segger embedded studio
I have enabled HFCLK timer and able...
I'm using nRF52840 and want to send a data of 200 bytes over BLE, but while adding the characteristic, if I give maximum length above 101 it does not accept it. Can someone...
I am working on a limited release project that has multiple devices which require programming. Part of the appeal of this device is its programmability so I am going to provide...
Hello,
I am looking for a low latency (end to end) wireless module for Joystick application and this is for a medical VR platform.
Latency requirement is <= 5ms.
Data...
Hi I'm new on zephyr
In my hardware the sensors around the soc are most of time not powered.
At Startup the OS initialise SPI, I2C, UART and some pins are set to 1....
Hi,
I am working on nrf52832, s132, SDK17, trying to trigger the saadc with the RTC2
This is my setup :
what I am trying to do is to periodically trigger a series...
I am using a custom board using the nRF52832. I have developed a number of applications using this board sucessfully using nRF5 SDK.,
I am porting a current application...
Project Zip:
Following is my setup:
Board : NRF52832 by Sparkfun( Link ) - Added pull-up resistor for TWI
Sensor: LIS2DH12(Custom breakout)
IDE: Segger Studio...
https://devzone.nordicsemi.com/f/nordic-q-a/79832/need-interface-mcu-initial-boot-firmware
apparently i can't update it anymore. does 'engineer assigned' mean that it can...
Hello,
I was measuring the current of a circuit I made using a PPK II and noticed I am getting two different readings from the two PCs I used (a work and a home PC).
Both...
hi
my first test do not run, bletooth is not enabled and could not get the bluetooth device led on board and signal on my mobile.
i following this link
https://infocenter...
