I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
One last issue to crack. This one has been in production for a while and hasn't caused any issues other than a little annoyance to the customer. By my measurement when RTC...
Hello,
In regards to the nRF Connect SDK...
I am looking into the possibility of switching out the current implementation of AES used by the Bluetooth firmware. I am curious...
the pin for XL0 and XL1 is P00 and P01
but in my project, I need P00 and P01 works as UART.
I set the parameter to start inner RC clock.and find that: LFCLKSTAT show the...
my costom board is based upon the BT840F fanstell board. I know that this board is based on the nrf52840 QIAA SOC. but I also understand that nrf52840 QIAA has different configurations...
I am working on custom hardware with an nRF52840. I have added the MCU boot in my earlier development as well but this issue I have never faced before.
Problem statement...
Hi,
iam trying to write the data in nvs which i give input through GATT.i can read and write in nvs when not using gatt,BT.
I have 2 codes,1 is working but without GATT...
Hello,
Board: custom board
Soc: nRF52840
SDK: nRF Connect SDK v2.8.0
I would like to know device mac address and use the mac address in advertsing.
can you please...
This page (v2.8.0) https://docs.nordicsemi.com/bundle/ncs-2.8.0/page/nrf/app_dev/device_guides/fem/fem_nrf21540_gpio_spi.html
Suggests copying the following into devicetree...
I am trying to get std::vector to work on nRF52840 running Zephyr in Visual Studio Code running v2.7.0 toolchain , but have been unable to do so. I found some similar tickets...
Hi nordic
I've try to enable 115200 baud UART on p0.9 and p.10 but I can't make it.
I just saw a thread about 52840 can't use 115200 uart at p0.9, p.10:
https://devzone...
Hello,
Is it possible to use the filtering options provided by the nRF52840 BLE sniffing firmware for Wireshark, in Tshark? Specifically the device address filtering....
Hello, I have two questions. 1. First, are these pins reserved in the SOC level or DK level? this if from the nrf52840dk device tree. meaning, if I have a custom board, should...
