hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hello,
We are working with the nPM1304-QEAA-R7 in a power management application and would like guidance on how to implement or connect a fuel gauge to this device. Specifically...
Hi I could not program the device via OpenOCD (current release) The programm tells me "invalid subcommand "write_image erase prog.hex" I modifed the nrf54L.cfg
added "flash...
I have a Power Profiler Kit II and have been using it for a few years without issue. I have been using it through the nrf Connect for Desktop software and the Power Profiler...
On the nRF54L15, is it possible to configure MCUboot so that the secondary image slot is stored in external flash connected via the SQSPI interface instead of internal flash...
Hi,
We're looking to integrate the NPM1304 in a product with a very small battery. As per the NPM datasheet we've selected a battery with a PCM.
We've previously seen...
We have a production system based on asset_tracker_v2 in V1.7.0 and V2.5.0. it normally connects and publishes fine 24/7. we have many sensors in the field. There are time...
Hello Nordic team,
I have a retail Thingy:91X device. IMEI: nrf-359404230239544
It connects to hello.nrfcloud.com, but I cannot add it to my own nRF Cloud account because...
We currently have a self-developed development board with NRF5340. The example program uses Bluetooth transparent transmission. Now I have added a GPIO pin: en_power is set...
When I was running the dm process of Connect SDK 3.0.2. I wanted to make one device as the initiator and six devices as the reflectors. I expect that the reflectors will not...
I am trying to external target using the nRF54L15DK and I get the following error.
Error: Failed with exit code 1. Failed to device info one or more devices: * 1057767167...
Hi,
We have developed a custom board with both nRF52833 as the BLE beacon and nRF7001 as WiFi. We have chose to use patch antenna with UFL connector for both. When we tried...
Hi,
I have now run most of the YAML test successfully on the Matter TH and while I usually need to restart the TH between runs it seems fairly reliable now. Before sending...
Hi experts, I'm using the example under nrf-bm/samples/bluetooth/ble nus, and I've configured prj.conf, but it's not working.
I've been struggling with this for ages...
I am getting an error trying to get coded phy working with a sysbuild configuration for a nrf5340 custom board:
I am trying to follow the Bluetooth: Peripheral Heart Rate...
Hi,
I am using the nRF5340 for my project.
In the production stage, I am facing an issue: after programming the nRF successfully, when I perform a readback, it shows...
