hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Unable to connect to Bonded weara with GATT 133 error. Currently, there is only one solution, turning on and off Bluetooth in the OS, which temporarily improves the connection...
Hello
new nRD5 SDK v17.1.0
Can you please help me to find more about:
1. "- NRFFOSDK-13484: Added an option in the Peer Manager to decide that a connection will not...
Hello,
I am currently developing an application on a single core application. I need to add a BLE part to this application. Currently, I have an OTA update procedure that...
Hello,
I'm trying to open an L2CAP connection and send some test data to the nrf52840 dev board from my computer. But my connections were timing out with 'Page Timeout'...
Hi ,
I have a question ,according to the official configuration and example, the ADC sampling voltage value is smaller than the actual voltage value. For example, the actual...
I have nrf52832 dk and soft dveice s132 am using ble app template code.
I need help in this code that as:
1. as i flash the code on dk, the device should be initally in...
I am using NCS v1.7.0 and have found that SES is not being configured properly for debugging/flashing. When I open the project in SES, building works fine, but when I try...
I have a theoretical question involving 6 24L01+ devices in PTX mode and one 24L01+ device in PRX mode.
Assuming a synchronized system, when one PTX finishes transmitting...
Hi,
I'm using the NRF9160DK board. I'd like to connect the UART port from 9160 to the 52840. The 9160 is running SLM firmware. The 52840 is running my code.
My question...
Some helpful pictures referenced in documentation (asset_tracker_v2_description.rst) are missing:
missing at least: figure:: /images/asset_tracker_v2_module_hierarchy.s...
I am using below environment for my project
NRF connect for desktop version 3.7.0 and Programmer v1.4.11 in windows 10, NRF52840 and Jlink debugger
I have tried multiple...
Hi!
I have a question regarding the scan timeout. The situation is the following:
On a nRF52840, I repeatedly perform scans every 120s (which is controlled by a CC Interrupt...
hi
I am using nr5340 and it adrvertise as nordic_lbs.. but i want to advertise through beacon sample. it still shows nordic_lbs in my mobile nrfconnect software. but it...
