Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hi ,
I need to preserve a clock counter without any drift or delay even the system having Soft reset,
I am using the Device BLE NUS bare metal example and running also...
Hello. I am developing a system where two radios are used - UWB and BLE. The first one is used almost all the time for communication and the BLE is used for beaconing let...
Dear Support,
i'm testing PCA10040 board. I'm using nRF5_SDK_15.3.0_59ac345 SDK package.
I'm testing the project ble_app_hts. I compile it and i download the firmware...
The download page for nRF52840 DK ( https://www.nordicsemi.com/Software-and-tools/Development-Kits/nRF52840-DK/Download#infotabs ) has download links for Heart Rate Monitor...
Hi DevZone,
I am new to nRF SoC and SEGGER. After installing all tools, I can build and run examples.
I run into a problem to add and enable a nRF driver, like "UARTE...
Hello, I am trying to develop a rehabilitation exercise service using Thingy52.
Thingy52 is the only device to accomplish my objective which needs motion detection using...
Hi,
I have nrf52840 DK and PCA63511 Power Profiler.
I have two questions:
1. The Average Current Consumption measured with profiler is 110uA (18 mA max, over 10 s...
Hi,
I have Raspberry pi board which i want to use it as a gateway .on which server will get set up.
nrf52840 will be the beacons which i have already set up for sending...
I am trying to use the NRF connect mobile app on android 8.1.0 to try and connect to a Bluetooth server serving GATT request to verify functionality.
The server is running...
Hello,
I am using these pre certified modules https://www.nicerf.com/product_147_88.html in a project which is basically nrf24l01+ with a PA and LNA.
These support ...
Hi,
Just been testing the data rate of write without response commands, I'm only getting about 250 bytes / second which seems incredibly slow?
I've just got a simple little...
Hi,
Is it possible to route an analoge signal through a digital GPIO pin to access the inner analoge pins of a nRF52840? I want to avoid using via-in-pad to keep the cost...
Hello,
I can't get the hex file to come out correctly in segger studio. What happens is, I build the solution and create the hex file but when I go to program my device...
Environment - nrf52832 - SDK 15.3
- SD 6.1.1 - with FreeRTOS
- Project: ble_app_buttonless_dfu
I have project with 4 timers and 3 tasks. Everything works fine when...
