We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
I am trying to run smart remote 3 on PCA10040/nRF52832.
I use gcc makefile to generate PCA63519-SR3_nRF52832_Shield firmware. SD firmware is downloaded by jflash and I use...
Hi,
I want to update firmware on nrf52832, but I have an error: DFU insufficient resources
I found this and this , so I try to program my softdevice with this file: /nRF5_SDK_15...
Hi，
there is a issue very strange, on a nrf52832 project, it use two gpio set to sense low level, one is p18, one is p29, I found there is no response for low level of p29...
We are using nRF52832 with SDK_15.3.0 running the Nordic UART service (NUS) example.
Out of the box we find that the uart event handler is continually being called with...
Hi,
I have an SPI peripheral on pins 26, 27, 28, 29 which I'm able to override the default system's UART0 pin assignments in nrf9160_pca10090ns.overlay. However when I enable...
Dear sir,
We have interfaced a charger ic with NRF52832. It is having a charging status pin to show completion of charge. It is having 3 states
1. High impedance (Battery...
Hello guys,
Something strange is happening here and I need your opinion about that... I have a custom board with nRF52840-based BL654 module on it. I am using SDK15.3.0...
Hello
I am using nrf52840 chip. I am having trouble configuring SAADC to read analogue input on two channels (one signal is VDD of the chip). I have already searched the...
I am trying to get connected with my Android App and I have noticed that sometimes when the user turns off Bluetooth and tries to enable it again after 20 minutes my Android...
I am working from the ble_app_hids_keyboard example. To support multiple centrals, I imagine the first step is changing NRF_SDH_BLE_PERIPHERAL_LINK_COUNT and NRF_SDH_BLE_TOTAL_LINK_COUNT...
Hi,
I am trying to set up eclipse + gdb + openOCD for debugging zephyr 2.0.0. applications on nRF52832. Following the official Zephyr documentation build-and-run-an-application...
Hello,
I am using NRF52832 with soft device 13.0.0 and Nordic's bootloader from the examples.
What I do is develop an application which stores some values in uicr registers...
I'm using 52810 with s112 stack.
And I need two PWM channel with different frequence. one channel set to 4KHz to cotroller BEEP, the other one set to 15Khz to control...
Hi, I've completed the first 3 BLE tutorials (about advertising and Services).
I've got notifications up and running on the peripheral by using a timer and hvx as in the...
